I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
We have made a custom board with nrf52840-QFAA. In the nordic board folder in Zephyr sdk, I could only find .dts file for nrf52840-QIAA.
And there is only one soc...
I use the nRF52840-QIAA and in the datasheet are 2 different reference designs for the ANT pin. 3 or 4 component matching and filter network. When I calculate the impedance...
Hi.
I would like to build a FW image for the nRF5340 net core which includes the two mode BLE controller part and Radio Test (like in the Radio Test sample). These two modes...
Hello Team, We are looking to do a POC on LE audio feature. Could you please clarify below query on the product nRF5340 DK which supports LE audio? We are planning to buy...
Dear Bluetooth Mesh experts,
The Android app needs to monitor the accessibility of all mesh nodes. One way to implement it would be to add a ping message to the firmware...
Hi,
Automatic installation from ToolChain Manager, no errors. Perform west update ,no errors. Check all the files ,no problem found.
Have reinstalled NCS for many times...
Hi,
Using MeshSDKv5 on custom nRF and nRF52DK
We are working on an LPN wireless PIR sensor so which sends a sensor status publish message on occupancy.
I have notiiced...
Hi,
I´m making my own custom nrf52811 board, but I do have some questions about programming. I want to program it with the nrf52dk using p20.
Now I did read that 3v is...
I installed nRF Connect SDK v2.0.0 and notice that the open Segger Embeded Studio button is not shown.
Also (may be related) opening Segger Embeded Studio from the SDK v1...
Hi,
I followed the instruction on infocenter as bellow,everything goes well ,but the cc.composition_data_get() command,no composition data was received . Any missing steps...
I developed a custom board using nrf52810-qfaa, i edited pca10040e-s112(sdk17.1.0) and changed the advertising led to BSP_BOARD_LED_3, as i have only one led on my board at...
Hi,
I am trying to debug ESB packets with the following setup:
1. PRX (NRF52810)
2..PTX (NRF52810)
3. Sniffer (NRF52832) ( modified PRX so that it returns without...
