I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi
I combine the hci_lpuart on the nRF52840 and a program that uses BLE on the nRF9160 on the nRF9160dk. I want to measure the current of this. At the moment I measure on...
I created a simple custom board (in VS Code 'Create a new board' Wizard) based on nrf9160 secure.
I copied the LED part of the original dts and I want to run blinky. ...
Hi Can someone, kindly suggest what are the pop up error notifications in the nRF mesh application for various scanning and provisioning of the BLE-Mesh network, if any document...
I used the Common Application Framework preview sample, with the following additions at end of prj.conf:
NCS 1.9.1 was used
The nrf52840dk then enters deep sleep after...
the cdc_acm speed is faster for my use in nrf5 sdk, but when i use the ncs,the cdc_acm example is use uart line, and the speed is slow, i receive data from rf2.4G radio, then...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
I'm working to implement a USB Mass Storage device which uses an external flash memory to store my application's data. I have an nrf52833 DK and a W25Q64FV NOR flash memory...
I/my admin installed the SDK and visual studio though the nRF connect tool chain manager.
When i open visual studio through the toolchain manager it prompts me
to "Select...
Hi All,
I am trying to set up nRF Connect SDK in Visual Studio Code. I am following the guide provided in the DevAcademy https://academy.nordicsemi.com/topic/exercise-1...
I am controlling the SPI via PPI at regular time intervals and it is working as expected.
However, I want the SPI to operate manually at any given time under certain conditions...
Hi
I am bumping my NRF Connect SDK application to nrf v1.9.1. However, I am getting the following error: `nrfxlib/nrf_802154/driver/src/nrf_802154_request_direct.c:196:66...
Hello Community,
I am tirelessly working on connecintg my icarus development board to LWM2M server, However there are no good examples to follow and do it with ease, there...
When I connect my PPK2 to my computer, it will not be detected:
Luckily there are instructions on how to downgrade to nRF Connect 3.7 in this (locked) thread.
nRF Connect...
Hi.
I use nrf52840.
sdk nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos.
Error calling xQueueReceive for the second time.
Here is the code and...
