Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
Hello,
I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Hello,
I've an issue migrating an NRF52840 project from NCS 1.7.0 to 1.9.1. I use PPI/GPIOTE to set a capacitor sensor charging pin and start a timer simultaneously, then...
I am using nRF52833 DK and I am running Light switch server in one DK and Client in another DK Advertising interval was way too high(around 9Second) so decided to change it...
Hello, we are trying to get software running on our custom board.
Last week we tried to test the software written on a development kit of the NRF9160 on to our custom board...
Did just encounter some nrfutil errors again.
First I was installing nrfutil on a new PC, and then trying to generate a settings package for a DFU file (nrfutil settings...
Hello everyone!
We need to implement Apple Notification Center Service (ANCS) in our nRF51 firmware so that the iOS application running in the background mode can receive...
Hi,
In the latest NCS V2.0.0 the profiler has been renamed but one of the sources hasn't and it causes a CMAKE error
https://github.com/nrfconnect/sdk-nrf/blob/main/subsys...
Hello,
I am using the ble_advertising module in sdk 17.0.2 on an nRF52840 with softdevice 140. I have the application working but want to convert to using coded PHY. After...
We are using nrfutil 6.1.3 on Ubuntu 20.04LTS and nRF5 SDK 17.0.2 We're using a copy of the dfu/secure_bootloader as the bootloader. We've changed NRF_BL_DFU_INACTIVITY_TIMEOUT_MS...
The nrf52840 defines 4 pwms. Attempting to enable pwm1, pwm2 or pwm3 using pinctrl through a device overlay results in build errors suggesting there is something wrong with...
Hello,
I am developing a driver for the vl53l5cx TOF sensor from ST, however their sequential write format looks as such:
This is problematic for me since I can get...
Hello, I was trying to run the Matter template example on board nRF5340 DK.
The nrf connect website example : https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello Nordic team!
We are using nrf52832 chip and soft device S332. System runs custom bootloader and main application.
We did not have any major problems with BLE...
Hi Nordic Team and programmers,
I have a Bluetooth peripheral built from the uart example and it has been working perfectly while operating a basic message based protocol...
Our product consists of a Texas MSP430 and a Nordic nRF52832 Chip, with serial/UART between
for MSP programming, debug and development : I'm using the official TI MSP-FET...
