My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
I would like to program the nRF dongles and Thingy 52, but i don't know how to choose right development kit to program the dongle and thingy.
Which one is best...
Hi,
We are developing a wireless protocol based upon 802.15.4 for nRF52840 and have some trouble with the MAC layer. To begin with, a mlme reset is requested and then an...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
I am attempting to integrate NVS within my custom application based...
Hello,
I noticed that nrf_ble_lesc_request_handler() hangs when I have NRF_CRYPTO_BACKEND_CC310_ENABLED and use a NRF_SDH_BLE_TOTAL_LINK_COUNT bigger than 5. Using the Oberon...
Hi,
I have the following error when trying to compile either the light_switch or light_bulb matter projects on nRF Connect SDK v1.8.0:
opening dependency file C:/Users...
Hi i have a problem i put buttonless dfu on my chip and everything went ok i can do OTA updates and everything works perfecly but i have a problem when i connect via j-link...
Hi,
Is there a low power consumption for battery powered long term (months) application for Nordic Thingy 91? I don´t need GPS position, just to receive sensor data and...
Hello
Using a Thingi91 with latest firmware and Asset Tracker v2. Connects to the tower, but cant seem to connect to the NRF Cloud. How can I check if it can reach any other...
Hello all
I am using the Thingi:91 in Sri Lanka. I can connect to the tower correctly, but cant get data connectivity yet. I am told by the operator that they use the following...
On nRF cloud I registered the ibasis sim card which came with the 9160DK and connected it to that 9160DK device. I'm now using a Fanstel BLG840F and wanted to know if the...
hello Nordic
i am using nrf52840, with zephyr
i wish to use the nrfConnect Tx power service to read and to SET my Tx power
but in ncs in zephyr/subsys/bluetooth/services...
Hi,
I am using nordic52840 dk board.
And i want to flash a bin file using nrfjprog command line.
For Hex file i am using below command
nrfjprog --reset --program blinky_pca10056...
Hi everyone,
We are using the nRF5340 and need to use an LFXO, not just for BLE, but also for the real-time clock that our product should provide.
Due to other requirements...
Dear Team,
Just I have purchased Thingy91. Please help with where I can see the demo to start with some basic example of transferring data. Mentioned that Pre-loaded assert...
