Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
This post is just to share with all of you (who would need it) a simple application interface (attached here) that uses the nRF52840 USB since we spent some painful...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
The main loop in our nRF9160 (NCS v1.8.0) is a typical main loop with semaphore following https://docs.zephyrproject.org/latest/kernel/services/threads/system_threads.html...
Hi,
I am trying to bring the nrf52 in sleep mode for 12 hours and broadcasting mode for other 12 hours. The idea behind it is to save the battery for longer life. What...
Hi,
I am testing NRF CTS and ANCS examples using iOS 14.7 (iPhone 6s) and 14.8(iPhone 10) and Zephyr 1.9.1. The peripheral (target) is a custom wearable running on nrf52840...
Hi team,
Our customer is working on a sensor related project targeting to use nRF9160-SICA, since their sensor will be placed in some places with high humidity and full...
Hi
I combine the hci_lpuart on the nRF52840 and a program that uses BLE on the nRF9160 on the nRF9160dk. I want to measure the current of this. At the moment I measure on...
I created a simple custom board (in VS Code 'Create a new board' Wizard) based on nrf9160 secure.
I copied the LED part of the original dts and I want to run blinky. ...
Hi Can someone, kindly suggest what are the pop up error notifications in the nRF mesh application for various scanning and provisioning of the BLE-Mesh network, if any document...
I used the Common Application Framework preview sample, with the following additions at end of prj.conf:
NCS 1.9.1 was used
The nrf52840dk then enters deep sleep after...
the cdc_acm speed is faster for my use in nrf5 sdk, but when i use the ncs,the cdc_acm example is use uart line, and the speed is slow, i receive data from rf2.4G radio, then...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
I'm working to implement a USB Mass Storage device which uses an external flash memory to store my application's data. I have an nrf52833 DK and a W25Q64FV NOR flash memory...
I/my admin installed the SDK and visual studio though the nRF connect tool chain manager.
When i open visual studio through the toolchain manager it prompts me
to "Select...
Hi All,
I am trying to set up nRF Connect SDK in Visual Studio Code. I am following the guide provided in the DevAcademy https://academy.nordicsemi.com/topic/exercise-1...
I am controlling the SPI via PPI at regular time intervals and it is working as expected.
However, I want the SPI to operate manually at any given time under certain conditions...
