I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi
I have a question about reset Bluetooth, how can I do that?
I don't want to reset the system only to reset ble, turn on and turn off the ble,
thanks and regards
Hi guys,
This is my first BLE project. I want to send sensor data from my nrf52840 dk to my dongle. I know how to make an advertise but I can’t find a way to send my sensor...
Hi!
We'd like to understand the most reliable way for DFU OTA our Nrf52840DK boards over a "serial" topology network?
We are using nRF5 SDK 15.2.0 and our configuration...
we have nRF52832 controller
now we would like to choose the softdevice S132 or S112
how can i select the softdevice?
where can i find the difference between S!32 and...
Hello, Technical support team
In the past, I contacted you to confirm nRF52832 application.
This time, I have a question for a external reset as follows.
My application...
Hey there,
We are working with NRF52832 WLSCP package,
We had stated certification process , for BQB testing need to use the Radio test example with UART between EUT...
Hi,
We are using Nordic BLE-NRF52833 Module one of our products. We are developing our own windows application(using C# language) to communicate the information to our Product...
Hi! Reading this ticket, and the nRF Connect SDK and nRF5 SDK statement , I understand that the PC-BLE-Driver, whether the Python or JS variant, are in maintenance mode, and...
Is there some example for Encode / Decode with AES algorithm in ECB and CBC modes using Segger studio?
For a start, I only need the ECB mode that should be implemented in...
I have checked the qDEC example, I don't know what it is doing, so I can directly say what I need. I connected a Hall sensor to two pins of 52840, and configured QDEC. I set...
Hi, I am just doing some testing using Nordic Thingy:91 and already available firmware and cloud. I am in the very initial stage of learning about it and preparing it for...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
Hi,
I'm trying out an application from the NRF SDK where I need to connect via putty or something similar to the serial port.
However, the port is not showing up (normally...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hi All,
I'm using nrf Connect SDK v1.7.0 with Vs Code
So here I can see in the debug prints that Bluetooth device is able to get connection successfull callback and Immediately...
