Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi,
I have a QSPI flash device with a weird bug (I think). Basically, when the RDSR command is executed, the HOLD pin needs to be held high otherwise the flash chip status...
Hi,
I'm developing with Segger and nRF52832.
I'm writing a code that makes two tasks into RTOS and sends data to BLE after I2C communication and SPI communication respectively...
Hi, I am using NRF5340 and I want to connect it with a 128x64 oled display with the I2C protocol (Scl, Sda, Vcc, Gnd), I have been trying to connect it for more than a week...
I want to interface 4 Digit Seven Segment display to nRF52840 Dongle and display the data(number) , which is received by it through Mesh protocol. I have successfully implemented...
I followed your step by step guide available on your site for installing the SDK and Toolchain. My system are Fedora 36 with VS Code IDE, but the system detects the errors...
Hi, I'm running a DFU ble_app_buttonless_dfu on nRF52833. Unfornately, my board is not supported it use pca10100. SDK 16 only supports pca10056 and 10040. I have used pca10056...
Hi! I've been struggling with a bug on a nrf51822 product I'm working on. It features some I2C devices, a screen and a couple of sensors. The mcu gets a watchdog reset due...
I have nRF52832 with factory reseted FW.
I need to make 52832 enter bootloader mode without pressing button. By just RPI4 PIN control program.
Planning PIN connection...
Hello Community!
I have an nRF52840 DK and the Segger Embedded Studio. I have Open nRF Connect SDK Project... and chosen serial_lte_modem. I build the solution modifying...
New design and I have a weird behaviour on the low voltage output of the internal LDO for CPU .
I have monitored DEC1 voltage on scope
Thats all the supply pins...
i am working with s140 on nRF-52840 and i send the data with sd_ble_gatts_hvx() and notification on custom service but the length of transmitted data always = 501 even if...
Hi All
I have been successfully using a jlink flasher for quite a few years now but after upgrading the segger drivers as i have always done ever couple of months i now...
I'm attempting to check out the bootloader under the nRF Connect SDK 2.0.0. This is critical for us to be able to move off of nRF5. I am starting with the smp_srv sample,...
I would need some help undestanding zephyr bootloader compatibility and west sign options. The issue I have is as follows:
I have an old project based on Zephyr RTOS v2...
Hello Devzone,
Working with nRF9160 SICA B1A system in package, and Nordic's ncs v1.6.1 (Zephyr RTOS 2.6.0) I recently observe that a device tree board setting i2c instance...
