I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi
I combine the hci_lpuart on the nRF52840 and a program that uses BLE on the nRF9160 on the nRF9160dk. I want to measure the current of this. At the moment I measure on...
I created a simple custom board (in VS Code 'Create a new board' Wizard) based on nrf9160 secure.
I copied the LED part of the original dts and I want to run blinky. ...
Hi Can someone, kindly suggest what are the pop up error notifications in the nRF mesh application for various scanning and provisioning of the BLE-Mesh network, if any document...
I used the Common Application Framework preview sample, with the following additions at end of prj.conf:
NCS 1.9.1 was used
The nrf52840dk then enters deep sleep after...
the cdc_acm speed is faster for my use in nrf5 sdk, but when i use the ncs,the cdc_acm example is use uart line, and the speed is slow, i receive data from rf2.4G radio, then...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
I'm working to implement a USB Mass Storage device which uses an external flash memory to store my application's data. I have an nrf52833 DK and a W25Q64FV NOR flash memory...
I/my admin installed the SDK and visual studio though the nRF connect tool chain manager.
When i open visual studio through the toolchain manager it prompts me
to "Select...
Hi All,
I am trying to set up nRF Connect SDK in Visual Studio Code. I am following the guide provided in the DevAcademy https://academy.nordicsemi.com/topic/exercise-1...
I am controlling the SPI via PPI at regular time intervals and it is working as expected.
However, I want the SPI to operate manually at any given time under certain conditions...
Hi
I am bumping my NRF Connect SDK application to nrf v1.9.1. However, I am getting the following error: `nrfxlib/nrf_802154/driver/src/nrf_802154_request_direct.c:196:66...
Hello Community,
I am tirelessly working on connecintg my icarus development board to LWM2M server, However there are no good examples to follow and do it with ease, there...
When I connect my PPK2 to my computer, it will not be detected:
Luckily there are instructions on how to downgrade to nRF Connect 3.7 in this (locked) thread.
nRF Connect...
Hi.
I use nrf52840.
sdk nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos.
Error calling xQueueReceive for the second time.
Here is the code and...
