this is a deflector test
I would like to ask you for your opinion, although it is not directly Nordic related, but indirectly, it is. The following:
The customer ICP...
Hi, I’m seeing a build failure after enabling SQSPI in the device tree when building with MCUBoot on NCS v3.2.1 for nRF54L15. The build works fine without SQSPI, but once...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
I was asked by Nordic tech support to create a new ticket, because ticket number 357092 had become a long a winding thread.
I need a simple utility I can offer to an end...
Hi,
I report some problems.
I have been using keil5,it work well. Because nRF Connect SDK doesn't know Keil
now i have used Segger Embedded Studio for a period of time...
Hi everyone. Here is my code for 2 different timers that put uc to sleep and wake it up(supposedly)
Definitions:
Create Timers:
Handlers:
Main() function...
I am working with the nRF5340 DK.
I am looking to sample an ADC pin to sample at a sampling frequency of at least 1kHz and I would like to use DMA to write the data directly...
Hi everyone, I implement nrf5_SDK_17.0.2 ble_app_uart example, but when I connect both GND wire and TX wire of the external device to my nRF52840 DK first, my nRF52840 DK...
Hi
As mentioned in this question: https://devzone.nordicsemi.com/f/nordic-q-a/69533/set-tx-power-on-zephyr-device , there is a sample to change the tx power using some HCI...
Hello,
I am trying to use the ble_app_rscs example app into the nRF5_SDK_17.1.0 package for connecting the nRF52840-DK board to the nRFToolbox Android application. However...
I have a small program that is to be used in production to test my device. It has to be scriptable so I'm using teraterm over rtt.
No external IO for a serial port.
Everything...
Hi Nordic,
Can you tell me how to remove commissioned a node from open-Thread ? Basically I want to remove a node from one network and put it in some other network. Are...
Hello,
I encountered a problem while trying to flash my PCA10040 nrf52 development kit.
I am able to compile my code in Segger Embedded Studio without a problem. The chip...
Hello:
I am using an nrf52840 on a custom board with W25Q01NV NOR Flash with the Nordic QSPI-NOR driver. Programming is with NCS v 1.8.0 (upgraded yesterday) and the VS...
Hi Team,
I am developing an application that required SPI communication with msp430.
But, some received characters are disorders, I see them by JLinkRTTViewer logs. For...
Hi
I'm using nRF51822 xxAA (256 Kbyte ROM). My code size are 66 690 byte, I'm using IAR.
Application memory setup:
This means that I have 131 KByte code size for my...
Hi,
I'm trying to configure my LTE modem (Icarus Board + nRF 9160 + SDK 1.7) with an external SIM.
For that i have to use the PDP configuration.
I use in my prj.conf...
Hi,
I am using SES and NCS SDK 1.6.1 under Win10.
A GPS module is connected to NRF5340, using an UARTE to communicate. The pin receiving GPS data is P0.31.
It works...
