I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I would like to use the GPIO and SPI NetCore of nRF5340. Is there any example code ?? Is it necessary to disable the GPIO and SPI of the AppCore of the nRF5340.
nrF5340 Appcore sw based on peripheral_lbs and netcore sw based on hci_rpmsg are working fine. However, the appcore sw will crash when I set
CONFIG_LSM6DSO=y in the pro...
Hi,
I am running peipheral_uart sample with nRF connect 1.9.1 . After running the sample for 10-15 min, I start getting the following error
"Not able to allocate UART...
I am unable to achieve low power after I enable UART. I disabled UART0 after enabling and the UART0 registers are all getting its default value after disabling.
But the...
Is there an HCI API to control the device and configure it to work with LE Audio? If so, is there an example of minimal configuration that will allow Audio DK to transmit...
I'm trying to integrate my application with the LWM2M Carrier library, and experiencing a hard fault when calling date_time_update_async(). This happens even if I call the...
After creating a new Ubuntu virtual machine to start fresh, I am still experiencing the issue below.
I re-installed the Connect SDK manually on the new virtual machine as...
Hi, I am trying to implement spi or i2c communication with a sensor using dma in master mode. can anyone give me some sample code on how to get spi/i2c peripheral over easy...
We designed an industrial gateway to communicate with sensors through Bluetooth. Both use nrf52832 chipset. However, there are many Bluetooth signals on the customer's site...
Hello,
I have a pure-C library that I'd like to build, and then import into another project that targets the nRF52832 (nRF5 SDK v16.0.0). The library has no dependencies...
Hello,
I'm using NCS v1.9.0 with a nrf5340-based device.
Is there a method to update the public key embedded in MCUBoot using DFU after the initial load? I'm looking...
Starting a new ticket since now I have a bit more details to describe what's going on
I have a custom model server that is configured to publish every 10 seconds with retransmit...
Hello. I can't program the nRF5340 of a couple of boards I recently received. I have it powered via USB (5V), and nRF_VDD is powered up to 1.8V as expected.
I've probed...
Hello,
In my project i am using stepper motor with nrf52840 and here i want to control the motor speed like in my application i want to expel fluid from the tube by pushing...
Dear sirs!
I need that timer (for example timer 3 or 4) will generate interrupt each 5 ms very precisely with precision of crystal (20 ppm). In 10 hours I cannot allow deviation...
