I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi Nordic
When I use JLINK to burn the firmware to the nRF52832 chip in the device, some devices cannot be programmed or cannot be programmed again after burning once
...
Hello, I've stumbled about a problem with the NrfConnect extension and Kconfig. It is quite simple: When a project directory contains a Kconfig file, it is used by west as...
I'm a bit confused by the "unidirectional" solutions offered as examples / documentation for the nRF5340 DK. I would like to build a BLE Audio headset that both receives and...
Hi
How is the ESB_EVT_IRQHandler started? NVIC_SetPendingIRQ(ESB_EVT_IRQ) is registered with on_radio_disabled(), but I don't know how to be started this handler in the...
Hi:
I use ncs 1.9.1, borad nRF9160-DK
sda-pin = <30>; scl-pin = <31>;
Config:
I added i2c2 in blinky, here is the source code.
I see i2c2 enabled in...
Hello,
I am experiencing issues with an nRF5340 DK. I would like to try the matter samples but every time I flash one of them, it results in fatal error and reseting loop...
fota_download_start copies the file but not host string into a static buffer. The comment implies that the download_client only requires this for the file path, though it...
Hello Devzone,
My name is Ted, and I recently came across a 2022 May 4 LPWAN Coverage document on one of Nordic Semi's technical guides. The specific guide is titled iBases...
Hi everyone, i have some problems with firmware and i hope someone can help me. I am using nRF52840 microcontroller and SEGGER Embedded Studio. Also I'm using the littlefs...
Hi ,
I want to use a pin on board, which is not used or initialized in dts file . my requirement is that I want to initialize that pin before booting process. ( that pin...
Hi,
I am using the :
bt_scan_filter_add (BT_SCAN_FILTER_TYPE_MANUFACTURER_DATA, &mfgData);
scan-filter works well.
However, keeping everything same, if setting...
I have added WDT to the blinky_freertos sample.
And I am debugging with SEGGER ozone.
building with SDK17:
If you reset the software in the debugger and start it,...
