i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello!
I have been trying to connect to T-Mobile's NB-IoT network using a NRF9160DK with a Twilio Narrowband sim, but have been unsuccessful so far. I have been able to...
Hello,
We designed a custom board with nrf9160 (modem firmware v1.3.1) that runs an asset tracker type application.
The application uses both, LTE and GNSS:
logs sensor...
Hi I am currently using an nRF52840 SoC and I already have both I2C buses in use, as my application requires multiple I2C sensors with the same address. That means I can't...
I'm using SEGGER's SystemView tool to get some insights on my code. I see which interrupt number is activated, and want to figure out which code actually runs.
looking at...
Hello,
I designed my first custom board and I'm happy to have it running. When I developed my test application, I used printk() to send debug information to the console...
I am working with nRF connect SDK with nRF5340DK. I am compiling code using nRF connect (ncs-1.8.0) for VS code with nrf5340dk_nrf5340_cpuapp board.
prj.conf as below, ...
I am trying to store data to the UICR using SDK16, mesh SDK 4.2.0 and the nRF52840 chip.
I want to write to the UICR once on runtime and never again. To avoid messing with...
Hi, all
I have some issues about developing on nRF connect SDK with VSCode:
Go to definition for macro always jumps to the wrong place. For example, BT_DATA_BYTES...
Hi all, I am using nrf52 with Softdevice 113 v7.0.1 and SDKv16 and FreeRTOS v10.0.1 and I am experiencing some issues with FreeRTOS timers expiring earlier than expected when...
Hi again,
A small edit to make this clear: Is it possible to update netcore using a single slot setup
After asking on another thread regarding something similar Simon...
I want to develop a low power device which enables connectivity for reading and writing data to its internal flash. The access should be with NRF_UART application
The access...
I was at 1st trying to use libuarte and it worked. However, talking to Edvin has convinced me to use something else as it is very resource heavy and I do not particularly...
Hi, I'm trying to connect an external I2C device to the nrf9160DK and read some registers. I'm using NCS v1.9.1.
I have my file nrf9160dk_nrf9160_ns.overlay defined like...
Hi!
I have been struggling with this for some time now.
I have a custom board with a nRF52810 that I want to run the ble_app_uart example as I wrote above.
I have made...
Peer Manager:
1. I am not sure whether my Nordic board and mobile app is just connected or paired, I am able to transfer data between the board and the mobile. How to...
