When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I am enabling bonding, but the nRF Connect application and it does not show the peripheral ( nRF52833 ) device is being bonded. Is there any other thing I am missing ?
SDK...
Hi,
Still have no answer for this problem, so I repeat again.
I have got the reply that the bootloader do not impact the application, so please check these videos.
VIDEO...
Hi guys,
When testing the MQTT connection on ncs 1.9.1, modem V1.3.1, when calling lte_lc_nw_reg_status_get to query the LTE signal status, the debugging found that there...
i have built and run "light switch " example given in nrf5340 sdk, i m using nrf5340dk to upload this example code, searched online , but unfortunately not getting any clue...
Hello,
In my project i am using stepper motor with nrf52840 and here i want to run my stepper motor for particular amount of time like i want to expel a particular amount...
I need a HCI controller only build for nRF52840, test on zephyr.
1) Build and flash for controller.
cd ~ /zephyrproject/zephyr/samples/bluetooth/hci_uart
mkdir build...
Hi,
The product we are developing needs to support extern Flash-based FOTA, so I downloaded the ble_extFlash sample from the following link for reference:
https://github...
PCA10121 schematic diagram U1 nRF5340 MCU is responsible for LE Audio, U11 nRF5340 interface MCU is responsible for programmer/debugger. Can you provide related software development...
I try to DFU on RaspberryPi OS by usb-serial. I put nRF52840 dongle on USB port of RPI4. And press reset button of the dongle.
I got error on nrftuil.
$ nrfutil dfu...
Hi there,
Yet again we are running into very basic issues with the nordic tools and software, and this is adding up to cost us massive amounts of time.
Within nrf connect...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
