Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi,
I have a model_handler.c which builds fine, but the moment I change it to model_handler.cpp, I get build errors saying "duplicate descriptor is not allowed". I am struggling...
Hi, There is code for vendor model element creation in nCS provided Chat client sample, as in below:
This works fine in "model_handler.c",
But when I import the same...
nrfjprog checks the target for 0xFFFFFF before attempting to write.
It should be successful not only if attempt to write the same value as is already present but also
...
Hei, jeg evalurere et Reinsdyr projekt der 30 Reinsdyr skal løper inne i en binge, er det mulig å motta kun beacon fra BLE taggen i nRFAPP fra de 30, hva er max antall når...
Hi!
Using the nrf5340-DK, I am preparing a code to be used on a custom board, where the pinning configuration will be different from that of the development board. I have...
Hi
I am using the nrf Connect extension in Visual Studio Code on a Window 11 machine together with C:\Nrf_Connect_SDK v1.9.1
After having installed the nrf Connect extension...
Hi,
I am working with nRF52832_dvk board, i am testing the OTA example as per in this link. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts...
Hello, I'm starting to design the pcb for the nrf52840. I looked but I saw that it is also possible to create it on two layers instead of four as the reference design teaches...
Hi,
I am trying to burst read FIFO of ADXL362 with zephyr adxl362 sample. 1 byte tx (read fifo command) and n byte rx ( reading the fifo data);
Zephyr is the last version...
Hi,
We tried to use Connect Interval 7.5ms with MTU 88B, both central and peripheral role are 52832, but observed disconnection after 30 sec.
Disconnection reason is 0x13...
Hello all,
Background: -NRF5340 -NRF SDK 1.9 -Zephyr 2.7.99
My objective is to send a data of 768 bytes by BLE. I use 4 notify to send this 768 bytes data (192 packets...
Hello,
I'm working on an application running on the nRF9160. The application is build on the Fanstel BLG840X and the code is shared between both the 52840 and 9160 on the...
Hello!
I have a problem updating network core firmware through MCUboot when NSIB is enabled (through "CONFIG_SECURE_BOOT=y" in my application prj.conf).
Without NSIB...
