Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I've an issue migrating an NRF52840 project from NCS 1.7.0 to 1.9.1. I use PPI/GPIOTE to set a capacitor sensor charging pin and start a timer simultaneously, then...
I am using nRF52833 DK and I am running Light switch server in one DK and Client in another DK Advertising interval was way too high(around 9Second) so decided to change it...
Hello, we are trying to get software running on our custom board.
Last week we tried to test the software written on a development kit of the NRF9160 on to our custom board...
Did just encounter some nrfutil errors again.
First I was installing nrfutil on a new PC, and then trying to generate a settings package for a DFU file (nrfutil settings...
Hello everyone!
We need to implement Apple Notification Center Service (ANCS) in our nRF51 firmware so that the iOS application running in the background mode can receive...
Hi,
In the latest NCS V2.0.0 the profiler has been renamed but one of the sources hasn't and it causes a CMAKE error
https://github.com/nrfconnect/sdk-nrf/blob/main/subsys...
Hello,
I am using the ble_advertising module in sdk 17.0.2 on an nRF52840 with softdevice 140. I have the application working but want to convert to using coded PHY. After...
We are using nrfutil 6.1.3 on Ubuntu 20.04LTS and nRF5 SDK 17.0.2 We're using a copy of the dfu/secure_bootloader as the bootloader. We've changed NRF_BL_DFU_INACTIVITY_TIMEOUT_MS...
The nrf52840 defines 4 pwms. Attempting to enable pwm1, pwm2 or pwm3 using pinctrl through a device overlay results in build errors suggesting there is something wrong with...
Hello,
I am developing a driver for the vl53l5cx TOF sensor from ST, however their sequential write format looks as such:
This is problematic for me since I can get...
Hello, I was trying to run the Matter template example on board nRF5340 DK.
The nrf connect website example : https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello Nordic team!
We are using nrf52832 chip and soft device S332. System runs custom bootloader and main application.
We did not have any major problems with BLE...
Hi Nordic Team and programmers,
I have a Bluetooth peripheral built from the uart example and it has been working perfectly while operating a basic message based protocol...
Our product consists of a Texas MSP430 and a Nordic nRF52832 Chip, with serial/UART between
for MSP programming, debug and development : I'm using the official TI MSP-FET...
