Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi everyone, i have some problems with firmware and i hope someone can help me. I am using nRF52840 microcontroller and SEGGER Embedded Studio. Also I'm using the littlefs...
Hi ,
I want to use a pin on board, which is not used or initialized in dts file . my requirement is that I want to initialize that pin before booting process. ( that pin...
Hi,
I am using the :
bt_scan_filter_add (BT_SCAN_FILTER_TYPE_MANUFACTURER_DATA, &mfgData);
scan-filter works well.
However, keeping everything same, if setting...
I have added WDT to the blinky_freertos sample.
And I am debugging with SEGGER ozone.
building with SDK17:
If you reset the software in the debugger and start it,...
Hi,
I have been working on the display from JDI LPM027M128C with the nrf52840 development kit. By consulting the datasheet of the display, it seems to work with the spi...
hi :
can you help me to solve this problem. The path of the example is bellow：
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Fexamples.html&cp...
Hello,
I am trying to work with the MCUBoot bootloader in my project. I was able to configure and build my project and it appears to run properly when I flash it to the...
I have a nrF52840-DK and would like to try some precompiled test, but I got an error when copying a hex file to it. The error message is that The currently active SWD interface...
Hello all, I am new to development as a whole, and have been tasked with getting my company's new nrf5340 audio kits working and creating replicable instructions for future...
We need to store a .fw firmware (or any binary/hex) image for an external device hanging off the nRF52833 in internal flash. What is the best way to integrate the image into...
Hi
after install sdk of nordic( Installing manually — nRF Connect SDK 1.9.99 documentation (nordicsemi.com) ) on ubuntu 20.04 LTS, when run EmbeddedStudio, i got the message...
Hello all,
for the last few weeks I am trying to workout the i2c protocol with the sensor and the nrf52dk , so far none of the solution that I have considered work. More...
Hi,
I upgraded to the newest SDK and now our SPI Code (RFID Reader) is not working anymore. Is there something that changed with parameters or anything else? If I step back...
