Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hello
My production ble performance is lower then nrf52DK.
How can I impove ble performance?
And I think there are two ways.
1. redesign PCB antenna (currently...
So, I'm trying to debug some code I've been working on, so set CONFIG_LOG=y in my prof.config file.
Now, when I try and builld, I get this error:
Error: Image size (0x36c54...
Hello everyone,
I am using the nrf52840 on the CDEBYTE E73-2G4M08S1C nRF52840 BLE 5.0 Wireless Transceiver. robiz.net/e73-2g4m08s1c
There are two device. One of them central...
nRF52840, SDK version 17.0.2_d674dde, SD140.
Our code uses the PPI extensively to manipulate some GPIOs and start SPIM transfers from peripherals using EasyDMA to store...
Hello all! I am trying to interface MPU6050 with nrf52832 dk using the following code. On the LOGGER, I see that the MPU isn't detected, despite I replaced the MPU. The if...
I wrote a reply to a 5-year old question which appeared to be related to my needs but the answer was not what I was looking for.
The case is very straight forward:
The...
Good morning Sir/Mam
i want to read data on serial using nrf9160 by segger. i have pic a sample from devzone "Uart". i have successfully build it and Run on board , but...
Hi,
I am having problem with UART on both NRF52 Devkit nad NRF52480 dongle. If I start from the example:
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart...
Hi,
at Bluetooth core specification v. 4.2, vol. 3, part G, chapter 4.9.3.
An Error Response shall be sent by the server in response to the Write
Request if insufficient...
I use the nrf examples direction_finding_connectionless_rx,firstly i have no attena array,the other as describled i do by steps.
I use two nrf5340 boards.with building,i...
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
Hello DevZone:
I can see that they are working on a module with WIFI6, my questions are the following.
Will the module have its own evaluation board or will it be integrated...
