I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
https://devzone.nordicsemi.com/f/nordic-q-a/69596/device-initialization-problems/285611#285611
had gone through above thread.
I am struck exactly at this point.
i...
Hi
I am using 52832 peripheral role.
sdk16.0
ble_uart add one character 0xff03 which have notify attribute
have these function
1. Use connectable broadcast on no...
Dear Nordic Engineers
I study central code,I find a param ble_gap_evt_adv_report_t
I can understand other param of ble_gap_evt_adv_report_t,but I don't understand set_id...
The NFC pins of my nRF52840 MCU have been set to be used as GPIO pins through the NFCPINS register. I can toggle the GPIO lines just but I find that after power on that the...
Hello,
been trying to add lte_lc_connect_async(lte_handler) to mqtt_simple, just like the way it is in sample aws_iot. Instead getting a failed response.
Now not sure...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
If while using the nRF Connect for Desktop you are seeing this message on the log
Make sure to installe the Universal JLink Segger from www.segger.com/.../
I'm using a sample from nRF connect SDK v1.91.1 for BLE peripheral. I'm trying to read one of the buttons on the development kit, but I'm not very sure how to use the button...
Have been trying to run nRF9160 LwM2M client sample. A problem is that it doesn't appear to be initialising the modem properly, by trying to access the network when the modem...
Hi,
I am trying to build the 'at_client' nRF9160DK sample app on a Mac and getting the following error:
CMake Error at /opt/nordic/ncs/v2.0.0/zephyr/cmake/modules/zephyr_module...
I am having the same problem as in
Case ID: 244142
devzone.nordicsemi.com/.../nrf52840_dk-spi-configuration
I am using nRF5340.
The problem I'm facing is that...
I use this code " node cli create-and-provision-device-cert"
But I am using nrf9160 ,so therefore I change this code to "node cli create-and-provision-device-cert --dk ...
This should be so easy, but it isn't. I started with the Dev Academy Lesson 6 I2C example. I wired up a little board with an I2C eeprom, created an overlay file to map the...
