Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
we got three nrf5340 audio dk, because we are still waiting for LC3 code authorization， so, I wonder how to config the sample project nrf5340_audio to use the open-source...
I am connecting a nrf52480 board (Adafruit Feather nRF52840 Express) as Connectivity chip and a custom board as Application chip for Nordic serialisation. Able to establish...
I am connecting a nrf 52480 board(Adafruit fether express) to a custom M4 cortex board with the help of nordic serialisation library. I have ported the serialisation library...
Hello all!
I'm using nRF52-DK to develop program which is controlled by smartphone (BLE) and do ADC&GPIO in the circuit.
GPIO acts like this: High-Low-High-Low.... it...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and do the following test:
I use nrf_gpio_cfg_output(), nrf_gpio_pin_set(); to set gpio P1.00 to high and use nrf_gpio_pin_input_get...
Hi Nordic:
Test with board nrf5340-dk ncs v1.9.1
prj.conf
# Console
CONFIG_LOG = y
CONFIG_LOG_PRINTK = y
CONFIG_LOG_DEFAULT_LEVEL = 3
# UartConsole
CONFIG_UART_CONSOLE...
Good morning:
I'm trying to develop the twi_scanner with the nrfx libraries. Everything seems to compile fine, but at the end of the Build process I get:
d:/ncs/v1.9...
Currently I am trying to adapt the Radio Test example to function on our custom hardware which uses the nRF52840 SoC. We need the Radio Test firmware to give access to the...
Hi All,
I have a nRF52840 DK board. Which I bought about 1.5 years ago. I used to do some development using Segger Embedded Studio those days.
Now I have setup the Zephyr...
Right now there are 2 supported codecs: SBC and LC3. It also looks like that they are implemented in software.
Can we have other audio codecs (i.e. LC3plus HR, aptX or LDAC...
Hi Nordic Support,
I have been waiting for many years to see our end-user devices (Android, iOS, Windows, and Linux) such as smartphones, tablets, and computers to support...
Hi, I hope you had a nice weekend.
In my project, I basically need to output some data over GPIO from a memory buffer (highs and lows). Currently I'm doing this with a timer...
Hi All!
I am using ble_app_multilink_central and ble_app_blinky examples for concurrent connections of 4 devices ( (1)nrf52833 as central and other (4) as peripherals(nrf52833...
I'm using modules from minew, those are MS50SFB2 based on nRF52810 and developing in nRF5_SDK_17.1.0_ddde560 and segger studio 6.30 on windows 10.
I was trying some examples...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle.When...
