Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello
I'm using an nrf52840 (PCA10059) together with an nrf24l01 (ESP32, MIRF Library).
My goal is to send a data packet from the nrf52840 which the nrf24l01 can receive...
Hi there,
the nRF58240 SoC supports a wide range of hardware-accelerated cryptography features using ARM's CryptoCell310. However, I'm unable to use many of the features...
I dwnload the nrf connect for desktop in my pc.i want to use the VS extension foe NRF.But i have had NCS 1.9.0 and 1.9.1 .The SDK of NCS is from my baidu pan.so i only install...
Hi! We are trying to make our project more secure following the Nordic documentation, but we absolutely don't know how to change the values of our registers, furthermore is...
I use the development version of NRF5340 DK, using the routine is ISO_broadcast, but the following error occurs, may I ask whether the controller does not support it?
...
Hi,
I just want to learn if we can use high-freq clock to measure time in nanosecs precision.
SoC: nRF52840
SDK: nRF Connect SDK (v1.9)
I know that it was not possible...
Hi guys,
I am experimenting with OTA buttonless DFU.
I included the Buttonless Secure DFU Service to my application and I managed to flash the new image over the air through...
Hi there,
As the title says, I only get an all white window whenever I open an app in nRF Connect for Desktop (this happens for all apps).
If I try to reload the window...
Hi Friends!
I want to do this on the nrf52840:
time start
do some code
time stop
print stop-start and get time
Im using nrf connect extension for VScode
Does...
I try to get the Direct Test Mode App to work on a Windows 10 Notebook. (for System Details see attached system report and verbose logfile).
Software versions:
nRF Connect...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
