Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Dears, I used NRF9160 and i have some questions about it: 1. the internal rtc is accurate or not ? is calibrated or need to be calibrated every time? 2. this rtc is internal...
Hi,
I use FDS to save my data in my application. Below is my fds list. All RECORD already have data from factory production.
#define FILE_ID 0x1111 #define RECORD_KEY_TORQUE_0...
Dear Members,
How can I scan continously if I loss the sensor,
I have made at this function :
static void ant_evt_handler(ant_evt_t * p_ant_evt, void * p_context)
...
Dear Members,
I got :
Could not find core in Coresight setup nRF52840 ? with PCA10059, it was working ok before,
Any solution for it ?
Kind regards,
Rixtronix...
Hello,
i've nRF5340-DK, 3 wire SPI oled model.
any one can change STM32F103 code for NCS1.9?
the oled can light on, but no show text, maybe SPI recv Font incorrect....
Am I the only one who finds Zephyrs I2C implementation a little cludgy? Or am I just missing something?
It may be that I'm just used to bare metal I2C but I can't seem to...
I'm working on a Central/Peripheral device and will need to set both:
CENTRAL_LINK_COUNT 1
PERIPHERAL_LINK_COUNT 1
It mentioned that if either of these values are changed...
Hi,
I'm trying the "Heart Rate Application" example on nRF52 DK. I successfully compiled and downloaded the hrs_example code to the board. When I used Toolbox app on the...
The Cortex-M4 exception handling and NVIC support late-arriving exceptions as discussed for example in the Cortex-M4 Generic User Guide. In this regard, my question is: What...
Hello,
I have been trying to get the UART working with EasyDMA on the NRF52832 development kit. I did have some success yesterday, but it's not working again today for some...
Hi,
I am working on a prototype which I have almost completed, I am using this NRF52832 chip, using BLE and creating a mesh network, where different nodes are communicating...
Hello,
I would like to know if Matter template example is compatible with nRF52840 Dongle. According to Matter Template example website ( developer.nordicsemi.com/.../README...
Hi,
I am using nrf5340 with Zephyr and nrf connect sdk 1.7.0 to drive two SPI bus devices off the same bus.
I have no problem configuring the SPI bus using nrfx_spim as...
