I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello supporters and enthusiasts,
I'm developing a BLE product which mainly works as central role for all scenarios.
The steps how the central controls to a peripheral...
With the release of NCS v2.0.0, is v1.9.x EOL? If not EOL, how long will it be supported, will there be a 1.9.2 or beyond?
Trying to decide if we should look at migrating...
Last year i asked about a custom nRF5340 board when using NCS V1.7.0 and the comment was to just copy the entire nRF5340DK into my custom board folder and modify the names...
Hello,
We have a pre-production design of a custom board that has an nRF5340 on it. We have built and programmed about 60 boards of this design without any issues using...
dear all，
I want to know how to estimate ram of softdevice use.
For example, as a central, how much ram will be required when adding a custom ble service,
and how much...
Hello
I added the mesh shell module to my app running on nRF52480 custom board and I am trying to provision and enable publication on the custom model I have
This produces...
Hii. I was using scheuler and wanted to know how this part of code works. The #define CRITICAL_REGION_ENTER() has opening bracket but it is closing after #define CRITICAL_REGION_EXIT...
Hi，
I use nRF9160 SPI to drive Epson's screen， The screen MAX writing apeed is 6M，But reading apeed is only 1M，So I need to switch SPI speed between read and write。
I...
I'm more or less copying the thingy:91-design. The Qourvo 12038 used in the design is EOL, and at the moment not available. It seems the alternatives use MIPI-interface. Can...
Hi,
I´ve been trying to improve data transmission from an nRF91 dev board through nb-iot to Azure IOT-hub and always got a socket disconnection event when I tried to send...
I would like to configure the TXD, RXD, RTS and CTS pins for the UART on the nRF52832.
I saw that the uart0 node ( nordic,nrf-uarte ) has attributes like rts-pin but they...
I got an nRF52 DK, took it from the box, plugged it into USB and turned it on. One LED was flashing softly and slowly.
Then I ran nrfjprog.exe --deviceversion --log and...
Hello, two related questions:
1) We're hiring a third party, Fortify to statically analyze our code base. I'm having trouble figuring out where I can modify the build tool...
Hi,
I already have a product which is running on NRF52810 (SDK S112)
Since the lack of CPU worldwide problem i found a stock of NRF52811.
I saw it's hardware is pin...
