Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello, I have a problem when I enable Bluetooth on my application. If I enable Bluetooth, I can't control gpio pin on Trace DATA. If I disable Bluetooth, I can. It's a hardware...
Hi,
nRFConnect SDK Sample not working (periodic_adv _sync)
I have two nRF52840 DK with nRFConnect SDK 1.7.1
Compiled and run on nRF52840 boards:
\ncs1.7.1 \zephyr...
Hi There
Is it possible to connect to nRF Cloud using a normal 4G/LTE Sim? I see the specs of the NRF9160 show that it supports full LTE and all the Bx bands.
If the answer...
hi,
I am beginner and I am converting an Arduino library to Nordic library, but I have this part code
what is mean begin, I am confused on this part , for example , TwoWire...
Hi,
I have been programming and testing ESB on the nRF52 DK using the Arduino IDE with the sandeepmistry code base, as it allows me to view serial output to a log screen...
Hi, I'm trying to enroll my nrf9160DK preview kit in nrfcloud. I've successfully done it with my Thingy91, but in process of upgrading modem on Thingy91 with my DK I forgot...
hardware board : 52840dk_52840
sdk : ncs1.7.1
IDE: Visual Studio Code
in our OTA design , we have new image download and stored in a LTE module, since our application...
Hello,
I use ST's mcu + Atmel radio IC + nRF21540 as the FEM. Use Atmel radio IC's IO to control the TX_EN and RX_EN pins for nRF21540 automatically.
I want to change...
We plan to create a BLE central device to communicate with our peripheral devices. Both sides are based on the nRF52840 using SD140. As we've already developed the peripheral...
Hi,
I just turned off compiler optimizations with CONFIG_NO_OPTIMIZATIONS=y (before that, code was working correctly). After the change, I noticed that my program is stack...
Use Microsoft Visual Studio Installer Projects to create .msi for nRF-Command-Line-Tools-10.14.0-x64.exe and other .exe files, but an error message will appear during execution...
Hi,
Is it possible to create two separate USB devices on nRF5340? My application requires three USB classes: Audio, CDC and DFU. Currently I am using all three in a composite...
Hi to all!
I am trying to use the nrf5340 as a MCU for a IoT project. I need to create a ECC key using secp256r1 and save it in the nrf5340 for later use.
I am using...
