Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I have a QSPI flash device with a weird bug (I think). Basically, when the RDSR command is executed, the HOLD pin needs to be held high otherwise the flash chip status...
Hi,
I'm developing with Segger and nRF52832.
I'm writing a code that makes two tasks into RTOS and sends data to BLE after I2C communication and SPI communication respectively...
Hi, I am using NRF5340 and I want to connect it with a 128x64 oled display with the I2C protocol (Scl, Sda, Vcc, Gnd), I have been trying to connect it for more than a week...
I want to interface 4 Digit Seven Segment display to nRF52840 Dongle and display the data(number) , which is received by it through Mesh protocol. I have successfully implemented...
I followed your step by step guide available on your site for installing the SDK and Toolchain. My system are Fedora 36 with VS Code IDE, but the system detects the errors...
Hi, I'm running a DFU ble_app_buttonless_dfu on nRF52833. Unfornately, my board is not supported it use pca10100. SDK 16 only supports pca10056 and 10040. I have used pca10056...
Hi! I've been struggling with a bug on a nrf51822 product I'm working on. It features some I2C devices, a screen and a couple of sensors. The mcu gets a watchdog reset due...
I have nRF52832 with factory reseted FW.
I need to make 52832 enter bootloader mode without pressing button. By just RPI4 PIN control program.
Planning PIN connection...
Hello Community!
I have an nRF52840 DK and the Segger Embedded Studio. I have Open nRF Connect SDK Project... and chosen serial_lte_modem. I build the solution modifying...
New design and I have a weird behaviour on the low voltage output of the internal LDO for CPU .
I have monitored DEC1 voltage on scope
Thats all the supply pins...
i am working with s140 on nRF-52840 and i send the data with sd_ble_gatts_hvx() and notification on custom service but the length of transmitted data always = 501 even if...
Hi All
I have been successfully using a jlink flasher for quite a few years now but after upgrading the segger drivers as i have always done ever couple of months i now...
I'm attempting to check out the bootloader under the nRF Connect SDK 2.0.0. This is critical for us to be able to move off of nRF5. I am starting with the smp_srv sample,...
I would need some help undestanding zephyr bootloader compatibility and west sign options. The issue I have is as follows:
I have an old project based on Zephyr RTOS v2...
Hello Devzone,
Working with nRF9160 SICA B1A system in package, and Nordic's ncs v1.6.1 (Zephyr RTOS 2.6.0) I recently observe that a device tree board setting i2c instance...
