Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I've an issue migrating an NRF52840 project from NCS 1.7.0 to 1.9.1. I use PPI/GPIOTE to set a capacitor sensor charging pin and start a timer simultaneously, then...
I am using nRF52833 DK and I am running Light switch server in one DK and Client in another DK Advertising interval was way too high(around 9Second) so decided to change it...
Hello, we are trying to get software running on our custom board.
Last week we tried to test the software written on a development kit of the NRF9160 on to our custom board...
Did just encounter some nrfutil errors again.
First I was installing nrfutil on a new PC, and then trying to generate a settings package for a DFU file (nrfutil settings...
Hello everyone!
We need to implement Apple Notification Center Service (ANCS) in our nRF51 firmware so that the iOS application running in the background mode can receive...
Hi,
In the latest NCS V2.0.0 the profiler has been renamed but one of the sources hasn't and it causes a CMAKE error
https://github.com/nrfconnect/sdk-nrf/blob/main/subsys...
Hello,
I am using the ble_advertising module in sdk 17.0.2 on an nRF52840 with softdevice 140. I have the application working but want to convert to using coded PHY. After...
We are using nrfutil 6.1.3 on Ubuntu 20.04LTS and nRF5 SDK 17.0.2 We're using a copy of the dfu/secure_bootloader as the bootloader. We've changed NRF_BL_DFU_INACTIVITY_TIMEOUT_MS...
The nrf52840 defines 4 pwms. Attempting to enable pwm1, pwm2 or pwm3 using pinctrl through a device overlay results in build errors suggesting there is something wrong with...
Hello,
I am developing a driver for the vl53l5cx TOF sensor from ST, however their sequential write format looks as such:
This is problematic for me since I can get...
Hello, I was trying to run the Matter template example on board nRF5340 DK.
The nrf connect website example : https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello Nordic team!
We are using nrf52832 chip and soft device S332. System runs custom bootloader and main application.
We did not have any major problems with BLE...
Hi Nordic Team and programmers,
I have a Bluetooth peripheral built from the uart example and it has been working perfectly while operating a basic message based protocol...
Our product consists of a Texas MSP430 and a Nordic nRF52832 Chip, with serial/UART between
for MSP programming, debug and development : I'm using the official TI MSP-FET...
