Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am trying to build the example for the Audio DK on an x86 Mac and am having trouble configuring the toolchain. I have followed the instructions from here: developer.nordicsemi...
It appears that Mesh Models do not perform transitions on their own (transition handling is not part of model itself).
Is this feature missing and is it planned to add it...
Since the previous topic was closed by accident and not able to reopen again, I will continue here.
Menon said:
Sorry I didn't get you well. You are using nRF5 SDK just...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Segger Embedded Studio 4.16
Aim: Controlling...
Hi ,
I have added simple on off mode in my previous application which was based on Generic ON OFF model. Code for simple on off model is added in both server and client...
Hello,
I have on nrf5340 an application, that meassures Temperature every second. I need to send the data to another nrf5340. I am going throw the bluetooth samples, but...
Hi
I'm trying to configure zephyr to build BLE host on the application core and BLE controller on network core on the nrf5340dk.
I was able to configure zephyr to run...
Hello,
I've been having issues trying to add MCUBoot to our application. The app is based on the Common Application Framework (CAF) with a structure based on the nrf_desktop...
hi,
sdk 17.1.0
Can I call " NRF_LOG_INFO" API back to back ? Does it copy the contents of the buffer (var) to an internal buffer ?
For example, in the below code, does...
Hi,
I am using nrf52833 ic with zephyr for firmware development my product is a battery based device and i want to reduce it power consumption when in ideal state what are...
I use both nrf52833 boards to do AOA test.But i use thr antenna array board of silab.The board are 16 antennas.I use the NCS version 1.9.1.
The next is my device stcture...
Hello all,
I have pinged the sensor on the "twi bus" successfully, now I am following the post on the read/write function that is needed to actually read the data off the...
Dear nordic engineers:
The only example I can find about flash is under zephyr/samples/drivers/spi_flash. However, the flash writing is pretty slow, and the MCU is halting...
I'm trying to record audio from Nano 33 BLE Sense which is using an nrf52840 microcontroller. But the default PDM library available doesn't allow me to record at a higher...
