Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I have followed the tutorials step by step on youtube( nRF Connect for VS Code, 1: Installation - YouTube ),but i still meet some errors when building the application.
The...
Dear Nordic,
Could you please suggest and and expamle or advice how to use in-project libraries properly (not 'externally built' as an know example shows). It's better to...
I'd like to use a nRF51822-based Bluefruit LE Sniffer to read BLE advertisements (embedded with sensor data), using a python script rather than Wireshark. I've tried pyshark...
Hello,
I have recently begun to use VSCode under Linux to develop with the nRF Connect SDK and have noticed a discrepancy in the extension's functionality when using Linux...
I would like to use the GPIO and SPI NetCore of nRF5340. Is there any example code ?? Is it necessary to disable the GPIO and SPI of the AppCore of the nRF5340.
nrF5340 Appcore sw based on peripheral_lbs and netcore sw based on hci_rpmsg are working fine. However, the appcore sw will crash when I set
CONFIG_LSM6DSO=y in the pro...
Hi,
I am running peipheral_uart sample with nRF connect 1.9.1 . After running the sample for 10-15 min, I start getting the following error
"Not able to allocate UART...
I am unable to achieve low power after I enable UART. I disabled UART0 after enabling and the UART0 registers are all getting its default value after disabling.
But the...
Is there an HCI API to control the device and configure it to work with LE Audio? If so, is there an example of minimal configuration that will allow Audio DK to transmit...
I'm trying to integrate my application with the LWM2M Carrier library, and experiencing a hard fault when calling date_time_update_async(). This happens even if I call the...
After creating a new Ubuntu virtual machine to start fresh, I am still experiencing the issue below.
I re-installed the Connect SDK manually on the new virtual machine as...
Hi, I am trying to implement spi or i2c communication with a sensor using dma in master mode. can anyone give me some sample code on how to get spi/i2c peripheral over easy...
We designed an industrial gateway to communicate with sensors through Bluetooth. Both use nrf52832 chipset. However, there are many Bluetooth signals on the customer's site...
Hello,
I have a pure-C library that I'd like to build, and then import into another project that targets the nRF52832 (nRF5 SDK v16.0.0). The library has no dependencies...
Hello,
I'm using NCS v1.9.0 with a nrf5340-based device.
Is there a method to update the public key embedded in MCUBoot using DFU after the initial load? I'm looking...
