I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I'm trying to wrap my head around the APP_USBD driver, but I'm running into a mental block. I am implementing a report descriptor for the Battery System usage page, and all...
Hello, I have been using the SPM to read the UICR->OTP[0] register in SDK1.2.1, 1.4.2, and 1.5.1 but it's not able to when I'm using version 1.9.1.
I have patched the \1...
Hello together,
Im currently doing my bachelor thesis and my task is to develop a user interface that can control a NRF52840 and write some parameters over UART.
Im...
Hello dear nordic team, how can I get all sensor data with the same time stamp in a uniform frequency? The 'Asset Tracker' application is on the Thingy:91. Best regards, ...
Hello,
I am successfully able to open and close adapter for nRF52840 using pc-ble-driver-py using python3.6.0 on my host armv7 Linux board.
But doing same inside the docker...
I got MCUBoot running using signed images. Now I want to enable encrypted images using the build tools, but how? I've found this pull request: https://github.com/zephyrproject...
Hi,
We are developing BLE firmware that will allow BLE pairing without bonding (but with PIN/Passkey that is entered from the phone). However, when I try this with nRFconnect...
Hello Nordic Support.
I would like to build and use a Sniffer using a PC (Windows 10), nRF52DK, and nRFConnect for desktop.
Please teach me about the following.
nRFSniffer...
Hi, I can successfully build the Matter light bulb example in nRF Connect SDK 1.9.1 but I fail to do the same in v1.9.99-dev1.
What did you change?
Here the error:
west...
Dear DevZone support team
I'm facing the following problem: My application uses the Zephyr's BLE stack and basically does not much beside parsing JSON-messages received...
Hi,
I tried to implement PPI for a very timing sensitive application. The sample PPI_trace uses the RTC but it is too slow for my application so I'd want ot use timer0...
Hi,
I am following these steps to build a sample project to try out OTA updates of the firmware. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software...
Hello,
We would like to use BLE to transmit a lossy data stream at high data rate. Looks like Isochronous channel is the best choice. How's the Isochronous channel is...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
