I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello!
I have been trying to connect to T-Mobile's NB-IoT network using a NRF9160DK with a Twilio Narrowband sim, but have been unsuccessful so far. I have been able to...
Hello,
We designed a custom board with nrf9160 (modem firmware v1.3.1) that runs an asset tracker type application.
The application uses both, LTE and GNSS:
logs sensor...
Hi I am currently using an nRF52840 SoC and I already have both I2C buses in use, as my application requires multiple I2C sensors with the same address. That means I can't...
I'm using SEGGER's SystemView tool to get some insights on my code. I see which interrupt number is activated, and want to figure out which code actually runs.
looking at...
Hello,
I designed my first custom board and I'm happy to have it running. When I developed my test application, I used printk() to send debug information to the console...
I am working with nRF connect SDK with nRF5340DK. I am compiling code using nRF connect (ncs-1.8.0) for VS code with nrf5340dk_nrf5340_cpuapp board.
prj.conf as below, ...
I am trying to store data to the UICR using SDK16, mesh SDK 4.2.0 and the nRF52840 chip.
I want to write to the UICR once on runtime and never again. To avoid messing with...
Hi, all
I have some issues about developing on nRF connect SDK with VSCode:
Go to definition for macro always jumps to the wrong place. For example, BT_DATA_BYTES...
Hi all, I am using nrf52 with Softdevice 113 v7.0.1 and SDKv16 and FreeRTOS v10.0.1 and I am experiencing some issues with FreeRTOS timers expiring earlier than expected when...
Hi again,
A small edit to make this clear: Is it possible to update netcore using a single slot setup
After asking on another thread regarding something similar Simon...
I want to develop a low power device which enables connectivity for reading and writing data to its internal flash. The access should be with NRF_UART application
The access...
I was at 1st trying to use libuarte and it worked. However, talking to Edvin has convinced me to use something else as it is very resource heavy and I do not particularly...
Hi, I'm trying to connect an external I2C device to the nrf9160DK and read some registers. I'm using NCS v1.9.1.
I have my file nrf9160dk_nrf9160_ns.overlay defined like...
Hi!
I have been struggling with this for some time now.
I have a custom board with a nRF52810 that I want to run the ble_app_uart example as I wrote above.
I have made...
Peer Manager:
1. I am not sure whether my Nordic board and mobile app is just connected or paired, I am able to transfer data between the board and the mobile. How to...
