Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
https://devzone.nordicsemi.com/f/nordic-q-a/69596/device-initialization-problems/285611#285611
had gone through above thread.
I am struck exactly at this point.
i...
Hi
I am using 52832 peripheral role.
sdk16.0
ble_uart add one character 0xff03 which have notify attribute
have these function
1. Use connectable broadcast on no...
Dear Nordic Engineers
I study central code,I find a param ble_gap_evt_adv_report_t
I can understand other param of ble_gap_evt_adv_report_t,but I don't understand set_id...
The NFC pins of my nRF52840 MCU have been set to be used as GPIO pins through the NFCPINS register. I can toggle the GPIO lines just but I find that after power on that the...
Hello,
been trying to add lte_lc_connect_async(lte_handler) to mqtt_simple, just like the way it is in sample aws_iot. Instead getting a failed response.
Now not sure...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
If while using the nRF Connect for Desktop you are seeing this message on the log
Make sure to installe the Universal JLink Segger from www.segger.com/.../
I'm using a sample from nRF connect SDK v1.91.1 for BLE peripheral. I'm trying to read one of the buttons on the development kit, but I'm not very sure how to use the button...
Have been trying to run nRF9160 LwM2M client sample. A problem is that it doesn't appear to be initialising the modem properly, by trying to access the network when the modem...
Hi,
I am trying to build the 'at_client' nRF9160DK sample app on a Mac and getting the following error:
CMake Error at /opt/nordic/ncs/v2.0.0/zephyr/cmake/modules/zephyr_module...
I am having the same problem as in
Case ID: 244142
devzone.nordicsemi.com/.../nrf52840_dk-spi-configuration
I am using nRF5340.
The problem I'm facing is that...
I use this code " node cli create-and-provision-device-cert"
But I am using nrf9160 ,so therefore I change this code to "node cli create-and-provision-device-cert --dk ...
This should be so easy, but it isn't. I started with the Dev Academy Lesson 6 I2C example. I wired up a little board with an I2C eeprom, created an overlay file to map the...
