I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I wanted to time stamp data which is sent via Bluetooth connection. Is there any pre defined functions to do that. Also please suggest any modifictions to be done...
Hi, I have a nRF52840 based Custom development board and a GSM module(AT command based) with UART and USB support. Because of lack of UARTs in nRF52840, I want to use USB...
Hi, I'm working on nRF9160 modem firmware update.
While working on nRF9160 modem, I found that it uses nrf_modem library which is precompiled library whose only API can...
Hello, I want to sampling voltage of 16 data sources, 8 of them are with amplifier, 8 of them directly connect to ADC pins, but I found that both nRF52810, nRF52832 and nRF52840...
I need to synchronise a time stamp on ant ANT slave with the master. Timesync would be ok but the message has to be acknowledged which ant timesync messages cannot do.
I...
Hi all,
I am trying to get my peripheral device to set an MTU size when connecting to the nRF Connect Android application that is not a value of 23. I have the following...
I've asked before about these two peripherals, the way they are presented is a little confusing.
I understand that UARTE has DMA possibilities, UART doesn't. Also that in...
I'm working on automating some of our builds for the nRF5340 in our CI, and
Currently, we can build these locally (on MacOS) with the NCS Connect VSCode toolchain, version...
Hi,
I'm experimenting the GPS on nrf9160 by using the ncs/samples/nrf9160/gps project. I set the GPS mode to be continuous mode. The 9160DK board is placed in a relative...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
What I want to do is to connect to Central, then bond and then disconnect.
Therefore, sd_ble_gap_disconnect...
Hi
This question is based on the NCS tag v1.8.0.
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
I got OK if I send a plain text to...
Hi Sir/Miss,
I import cts (current time service) as previous topic which is as link .
I have a compatibility issue in different phone.
The tested conditions are as...
Hi,
I'm thinking of doing a send / receive test of nRF52832. The Bluetooth test set uses MT8852B (anritsu).
At that time, it is necessary to send a signal by HCI or 2...
In the nrfConnect SDK 1.4 there is a sample for chainable RGB LEDs ../ ncs/zephyr/samples/drivers/led_ws2812
I want to use this with nrf9160 so I created nrf9160dk_nrf9160ns...
