Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello,
We are working toward certification of our product and conducting TRP/TIS measurements. The TRP and TIS are not matching up with the conducted output power and...
I'm having a hard time developing for Nordic Hardware right now as it seems that the hardware is not recognized by VSCode/NrfConnect anymore. Under the Connected Devices Section...
Dear,
I use an nrf5340 dk with sdk 1.8.0 for vscode. I'm now playing with the central_and_peripheral_hr example and I want to change the advertisement packet. How and where...
Hi,
I have an issue in regard to Matter. I would like to commision a device in my network, but I don't know why the Python CHIP Controller returns this error every time...
Hello supporters and enthusiasts,
I'm developing a BLE product which mainly works as central role for all scenarios.
The steps how the central controls to a peripheral...
With the release of NCS v2.0.0, is v1.9.x EOL? If not EOL, how long will it be supported, will there be a 1.9.2 or beyond?
Trying to decide if we should look at migrating...
Last year i asked about a custom nRF5340 board when using NCS V1.7.0 and the comment was to just copy the entire nRF5340DK into my custom board folder and modify the names...
Hello,
We have a pre-production design of a custom board that has an nRF5340 on it. We have built and programmed about 60 boards of this design without any issues using...
dear all，
I want to know how to estimate ram of softdevice use.
For example, as a central, how much ram will be required when adding a custom ble service,
and how much...
Hello
I added the mesh shell module to my app running on nRF52480 custom board and I am trying to provision and enable publication on the custom model I have
This produces...
Hii. I was using scheuler and wanted to know how this part of code works. The #define CRITICAL_REGION_ENTER() has opening bracket but it is closing after #define CRITICAL_REGION_EXIT...
Hi，
I use nRF9160 SPI to drive Epson's screen， The screen MAX writing apeed is 6M，But reading apeed is only 1M，So I need to switch SPI speed between read and write。
I...
I'm more or less copying the thingy:91-design. The Qourvo 12038 used in the design is EOL, and at the moment not available. It seems the alternatives use MIPI-interface. Can...
Hi,
I´ve been trying to improve data transmission from an nRF91 dev board through nb-iot to Azure IOT-hub and always got a socket disconnection event when I tried to send...
