We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
I wanted to time stamp data which is sent via Bluetooth connection. Is there any pre defined functions to do that. Also please suggest any modifictions to be done...
Hi, I have a nRF52840 based Custom development board and a GSM module(AT command based) with UART and USB support. Because of lack of UARTs in nRF52840, I want to use USB...
Hi, I'm working on nRF9160 modem firmware update.
While working on nRF9160 modem, I found that it uses nrf_modem library which is precompiled library whose only API can...
Hello, I want to sampling voltage of 16 data sources, 8 of them are with amplifier, 8 of them directly connect to ADC pins, but I found that both nRF52810, nRF52832 and nRF52840...
I need to synchronise a time stamp on ant ANT slave with the master. Timesync would be ok but the message has to be acknowledged which ant timesync messages cannot do.
I...
Hi all,
I am trying to get my peripheral device to set an MTU size when connecting to the nRF Connect Android application that is not a value of 23. I have the following...
I've asked before about these two peripherals, the way they are presented is a little confusing.
I understand that UARTE has DMA possibilities, UART doesn't. Also that in...
I'm working on automating some of our builds for the nRF5340 in our CI, and
Currently, we can build these locally (on MacOS) with the NCS Connect VSCode toolchain, version...
Hi,
I'm experimenting the GPS on nrf9160 by using the ncs/samples/nrf9160/gps project. I set the GPS mode to be continuous mode. The 9160DK board is placed in a relative...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
What I want to do is to connect to Central, then bond and then disconnect.
Therefore, sd_ble_gap_disconnect...
Hi
This question is based on the NCS tag v1.8.0.
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
I got OK if I send a plain text to...
Hi Sir/Miss,
I import cts (current time service) as previous topic which is as link .
I have a compatibility issue in different phone.
The tested conditions are as...
Hi,
I'm thinking of doing a send / receive test of nRF52832. The Bluetooth test set uses MT8852B (anritsu).
At that time, it is necessary to send a signal by HCI or 2...
In the nrfConnect SDK 1.4 there is a sample for chainable RGB LEDs ../ ncs/zephyr/samples/drivers/led_ws2812
I want to use this with nrf9160 so I created nrf9160dk_nrf9160ns...
