At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I would like to use the GPIO and SPI NetCore of nRF5340. Is there any example code ?? Is it necessary to disable the GPIO and SPI of the AppCore of the nRF5340.
nrF5340 Appcore sw based on peripheral_lbs and netcore sw based on hci_rpmsg are working fine. However, the appcore sw will crash when I set
CONFIG_LSM6DSO=y in the pro...
Hi,
I am running peipheral_uart sample with nRF connect 1.9.1 . After running the sample for 10-15 min, I start getting the following error
"Not able to allocate UART...
I am unable to achieve low power after I enable UART. I disabled UART0 after enabling and the UART0 registers are all getting its default value after disabling.
But the...
Is there an HCI API to control the device and configure it to work with LE Audio? If so, is there an example of minimal configuration that will allow Audio DK to transmit...
I'm trying to integrate my application with the LWM2M Carrier library, and experiencing a hard fault when calling date_time_update_async(). This happens even if I call the...
After creating a new Ubuntu virtual machine to start fresh, I am still experiencing the issue below.
I re-installed the Connect SDK manually on the new virtual machine as...
Hi, I am trying to implement spi or i2c communication with a sensor using dma in master mode. can anyone give me some sample code on how to get spi/i2c peripheral over easy...
We designed an industrial gateway to communicate with sensors through Bluetooth. Both use nrf52832 chipset. However, there are many Bluetooth signals on the customer's site...
Hello,
I have a pure-C library that I'd like to build, and then import into another project that targets the nRF52832 (nRF5 SDK v16.0.0). The library has no dependencies...
Hello,
I'm using NCS v1.9.0 with a nrf5340-based device.
Is there a method to update the public key embedded in MCUBoot using DFU after the initial load? I'm looking...
Starting a new ticket since now I have a bit more details to describe what's going on
I have a custom model server that is configured to publish every 10 seconds with retransmit...
Hello. I can't program the nRF5340 of a couple of boards I recently received. I have it powered via USB (5V), and nRF_VDD is powered up to 1.8V as expected.
I've probed...
Hello,
In my project i am using stepper motor with nrf52840 and here i want to control the motor speed like in my application i want to expel fluid from the tube by pushing...
Dear sirs!
I need that timer (for example timer 3 or 4) will generate interrupt each 5 ms very precisely with precision of crystal (20 ppm). In 10 hours I cannot allow deviation...
