At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello, I am trying to add a watchdog timer to my code which consists of THREE threads, so I referred to the task_wdt example in Zephyr/Samples/Subsys for SDK1.6.1.
Based...
Hi,
I wonder if there is a smart and easy way to implement a fallback if I use the MQTT connection with a static IP. What I want is if the IP fails to connect it tries again...
this error shows after the 100% completion of memory flash as shown in the screenshot below. after showing the error , nrf52840 pulsing led turns off automatically.
Note...
Greetings All,
I am trying to connect an nrf52840dk board to an nrf52840dongle for wireless serial communication.
I flashed the nrf52840dk with the central_uart sample...
Hello,
I am using nrf52832 and i am using a SW similar to the beacon.
I tried 2 configuration:
tx_power = 0 (0 dbm)
tx_power = 4 (4 dbm)
I tried to measure the...
Hello,
I'm familiar with the GPIO and GPIOTE peripherals,
The GPIOTE has 8 channels, so it can use 8 GPIO pins to fire interrupts.
Some questions:
- Can the 8 Channels...
Hi ,
I have compiled in Heart rat relay into my app; can scan and connect to simulator and garmin HR straps; but fail to connect to polar. My debug log shows...
...
I've successfully built the 'direction_finding_connectionless_tx' project and flashed that to an nRF52833dk, and built the 'direction_finding_connectionless_rx' project with...
Hi,
I'm using a NRF52811 on a custom board and I would like to change a project from a NRF52832 with S132 to it.
I only use supported functions from the S113, but I...
how to set the High-drive QSPI?
NRF_GPIO_PIN_H0H1
nrf_gpio_cfg ( mosi_pin ,
NRF_GPIO_PIN_DIR_OUTPUT ,
NRF_GPIO_PIN_INPUT_CONNECT ,
NRF_GPIO_PIN_NOPULL ,
NRF_GPIO_PIN_H0H1...
Environment:
- OS: Ubuntu 20.04 (Docker container)
- NRF SDK: v1.4.0
- Zephyr: v2.4.0-ncs1
I am trying to build my project for native_posix. I am getting some build...
Hi, I have a NRF52840 DK. I want to use ble_app_uart_c and my peripheral is NRF52840 Dongle and also I want to receive and transmit special frame over ble. I have a problem...
Hello Nordic engineer,
I used SDK15.3.0 and nRF52811
I want to ask three questions,
(1)
Can a session be opened forever?
I will frequently use BLE+ESB in my...
