Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi
I have a question about reset Bluetooth, how can I do that?
I don't want to reset the system only to reset ble, turn on and turn off the ble,
thanks and regards
Hi guys,
This is my first BLE project. I want to send sensor data from my nrf52840 dk to my dongle. I know how to make an advertise but I can’t find a way to send my sensor...
Hi!
We'd like to understand the most reliable way for DFU OTA our Nrf52840DK boards over a "serial" topology network?
We are using nRF5 SDK 15.2.0 and our configuration...
we have nRF52832 controller
now we would like to choose the softdevice S132 or S112
how can i select the softdevice?
where can i find the difference between S!32 and...
Hello, Technical support team
In the past, I contacted you to confirm nRF52832 application.
This time, I have a question for a external reset as follows.
My application...
Hey there,
We are working with NRF52832 WLSCP package,
We had stated certification process , for BQB testing need to use the Radio test example with UART between EUT...
Hi,
We are using Nordic BLE-NRF52833 Module one of our products. We are developing our own windows application(using C# language) to communicate the information to our Product...
Hi! Reading this ticket, and the nRF Connect SDK and nRF5 SDK statement , I understand that the PC-BLE-Driver, whether the Python or JS variant, are in maintenance mode, and...
Is there some example for Encode / Decode with AES algorithm in ECB and CBC modes using Segger studio?
For a start, I only need the ECB mode that should be implemented in...
I have checked the qDEC example, I don't know what it is doing, so I can directly say what I need. I connected a Hall sensor to two pins of 52840, and configured QDEC. I set...
Hi, I am just doing some testing using Nordic Thingy:91 and already available firmware and cloud. I am in the very initial stage of learning about it and preparing it for...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
Hi,
I'm trying out an application from the NRF SDK where I need to connect via putty or something similar to the serial port.
However, the port is not showing up (normally...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hi All,
I'm using nrf Connect SDK v1.7.0 with Vs Code
So here I can see in the debug prints that Bluetooth device is able to get connection successfull callback and Immediately...
