Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello supporters and enthusiasts,
I'm developing a BLE product which mainly works as central role for all scenarios.
The steps how the central controls to a peripheral...
With the release of NCS v2.0.0, is v1.9.x EOL? If not EOL, how long will it be supported, will there be a 1.9.2 or beyond?
Trying to decide if we should look at migrating...
Last year i asked about a custom nRF5340 board when using NCS V1.7.0 and the comment was to just copy the entire nRF5340DK into my custom board folder and modify the names...
Hello,
We have a pre-production design of a custom board that has an nRF5340 on it. We have built and programmed about 60 boards of this design without any issues using...
dear all，
I want to know how to estimate ram of softdevice use.
For example, as a central, how much ram will be required when adding a custom ble service,
and how much...
Hello
I added the mesh shell module to my app running on nRF52480 custom board and I am trying to provision and enable publication on the custom model I have
This produces...
Hii. I was using scheuler and wanted to know how this part of code works. The #define CRITICAL_REGION_ENTER() has opening bracket but it is closing after #define CRITICAL_REGION_EXIT...
Hi，
I use nRF9160 SPI to drive Epson's screen， The screen MAX writing apeed is 6M，But reading apeed is only 1M，So I need to switch SPI speed between read and write。
I...
I'm more or less copying the thingy:91-design. The Qourvo 12038 used in the design is EOL, and at the moment not available. It seems the alternatives use MIPI-interface. Can...
Hi,
I´ve been trying to improve data transmission from an nRF91 dev board through nb-iot to Azure IOT-hub and always got a socket disconnection event when I tried to send...
I would like to configure the TXD, RXD, RTS and CTS pins for the UART on the nRF52832.
I saw that the uart0 node ( nordic,nrf-uarte ) has attributes like rts-pin but they...
I got an nRF52 DK, took it from the box, plugged it into USB and turned it on. One LED was flashing softly and slowly.
Then I ran nrfjprog.exe --deviceversion --log and...
Hello, two related questions:
1) We're hiring a third party, Fortify to statically analyze our code base. I'm having trouble figuring out where I can modify the build tool...
Hi,
I already have a product which is running on NRF52810 (SDK S112)
Since the lack of CPU worldwide problem i found a stock of NRF52811.
I saw it's hardware is pin...
