When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi guys,
So lately, I decided to update the sdk from 4.1.0 to 4.2.0 and there are some problem that I can not solve myself. So I use the macro ZB_ZCL_REGISTER_DEVICE_CB...
Dear Nordic,
We are developing nRF21540 + nRF5340 solution.
As there seems to be many versions of matching components depending on which source of information is used...
The RPM package for Linux x86 64 bit has its architecture set to amd64, but the correct value should be x86_64. This problem prevents installing the RPM on current versions...
I have a question about BD_ADDR.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) device: EYSHJNZWZ (nRF52832)
1) Is it possible to change...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
Dear customer support,
the datasheet of the NRF52810 states that its operating temperature is: -40...+85°C
Could you please clarify the following points?
- How is...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello !
I'm currently discovering the VS code extension for nRF Connect SDK and I whish to give some feedbacks of missing / odd features. I hope this is the best place...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
Hi,
Since NCS 2.0 dosent support SES anymore, I've started using nrf connect in vscode recently.
Here are some problems I met:
1. It takes almost 5 mins to loading everytime...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
