Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear sirs!
I need that timer (for example timer 3 or 4) will generate interrupt each 5 ms very precisely with precision of crystal (20 ppm). In 10 hours I cannot allow deviation...
been having issues trying to get LittleFS to work on external SPI NOR Flash. I get linker errors leading me to believe something is missing in a config. I’ve looked at many...
I previously was evaluating the basic nRF5340 DK and installed the toolchain manager and the nRF Connect SDK v 1.9.1.
I now am looking at the Audio DK, and its documents...
Dear ,
I am using nrf52833dk configured as nrf52820 using NCS1.7.0 SDK. I am experiencing some difficulties in regard to the SPI.
I have configured SPI as followed, but...
Hi all,
I am working on nrf52840 chip with SDK 17.0.2.
Our application runs smoothly and we want to add it the capabilities of upgrading another nrf52840 chip using Nordic...
Hi,
I need to create a device that can support up to 10 concurrent connection with MITM protection, so I would like to implement bonding with a passkey.
I started my project...
I am using: nRF52840 nRF Connect 1.9.1 VS Code W5500 for ethernet Azure IoT Hub
I have the above (mostly) working. My code is based on the Azure IoT Hub sample for the 9160...
hi support team,
we have one ticket about lesc and freertos: https://devzone.nordicsemi.com/f/nordic-q-a/59655/lesc-and-freertos ;
it's about nrf_ble_lesc_request_handler...
We are trying to make DFU over BLE with external flash to overcome the large application size.
Environment: ->nrf52832 - >nRF Connect SDK (v1.8.0) - >External flash (W25Q64JV...
We are planning to evaluate concurrent GPS and LTE(NBIoT) operations on the nRF9160-DK using AT commands.
Please provide guidance on how to obtain GPS NMEA data and LTE...
Hi there,
This morning I updated to the latest version of the nrf connect for desktop, along with all the extensions (LTE Link Monitor, Programmer, Toolchain Manager). ...
Hi, I'm developing an application using app_timer to send data to server. Detail about my application
1. I get data from server the value of timer
2. dynamic change timer...
Hello, I am trying to implement the nrf5-calendar-example for the nrf connect SDK for the board nrf9160dk_nrf52840. I am able to compile the code for this board with the nrf...
Our application requires switching between NB-IoT and LTE-M without flashing firmware of any part, including modem. We were recommended the nRF9160/nRF52840 due to this capability...
