Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hello,
Our project is based on the "ble_app_template" example with added BLE custom profile.
We have been developing our software on the u-blox "BMD-300 evaluation board...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I had toolchain manager 0.10.3 and a project using NCS 1.91. Unfortenuately I have updated the Toolchain manager to 1.0.0 and now my project does no longer show up and the...
Hi
I have build a sample project nRF5430_audio for nRF5340 Auido DK(two DK, one for gateway, one for headset), following the guide: nRF5340 Audio — nRF Connect SDK 2.0.99...
Hi,
I work on a project that uses the dfu target library for firmware updates. This has been working flawless until I added task watchdogs.
The problem that I see is that...
Hello,
--> I want to read some analog values from Pressure sensor. I don't know how to read analog input from sensor. Can you give/provide me the code which having an only...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
I want to use the external flash memory MX25R6435F to run my code which has a big size on my arduino nano 33 ble but I'am a newbie and I don't find supports that can help...
I use PCA10059 demo board,receive BT data by" nrf connect for desktop",yesterday it is ok,but today when I plug it into my PC,it can't be recognized.and no any indicator,...
Hello,
In the Zigbee Network Coordinator example when flashing new file to nrf52840-DK the Zigbee network steering automatically starts. How do I disable auto-start of network...
When using the distance measurement function newly added to the reference point by THE GNSS routine of NCS V2.0.0, it is found that each measurement has a deviation of 30...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
