Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Dear Members,
Where can I download
PCA10059 altium schematic and PCB files ?
I have the board here and I need those files for further production stage,
Regards...
Hi Team,
We are using nRf52840 SOC for our project and for each code change test we need to burn FW build on real hardware. Using real hardware setup increase testing feedback...
I am using the zigbee examples and want to see the RSSI value in any received packet.
I am calling zb_zdo_get_diag_data(short_addr, &lqi, &rssi) in zboss_signal_handler...
Hello,
So far, I've worked with the EVK testing the CDC & ESB features for our purposes.
Right now, I want to move to development and we acquired the dongles (P/N 451...
Hello,
We have to program an external QSPI flash which is connected to an nrf52840 SoC using the J-Flash application from SEGGER.
For this requirement I followed the instruction...
I get the following error if I try to unprovision device via ADV Bearer:
Problem is reproducible on "ncs\v1.7.0\nrf\samples\bluetooth\mesh\light" project if Light CTL...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
zigbee stops working when I use timer 2 for asynchronous UARTE operation. Tell me where to see which stack uses which periphery. Or is it some kind of mistake on my part?...
Hello,
In my project i am using nrf52840 and i have change the default UART pins to P1.3 (TX) and P1.4(RX) and while using virtual UART like BLE UART i mean in the sense...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Looking through the forum, I found this great post with an awesome and very helpful document that displays the ins and outs of BLE on Android ( BLE_on_Android_v1.0.1.pdf ...
Hi, I want to upload the code to external nrf52832 chip(which is on the custom-made PCB) using nrf52DK board.
First, I tried to check uploading the nrf52832 chip on nrf52DK...
Hello Devzone Community,
My name is Ted, and I am continuing work on an nRF9160 based, battery powered custom board firmware. I recently posted a couple of tickets here...
Hello. I am doing current measurements on nrf9160dk while sending ~1kb json file through mqtt. I am following this guide: https://infocenter.nordicsemi.com/topic/ug_nrf91_dk...
