Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi, I have external PCB, looks like this:
Need help with flashing the nRF52832 chip via nRF52 DK, please. External PCB have identical pin assignments as QFN48 pin assignments...
So, i just got some modules from minew, those are MS50SFB2 ( https://www.minew.com/product/nrf52810-ms50sfb2/ ) based on nRF52810. I uploaded the blinky example on one of...
Hi,
I am using nRF SDK 1.9.1. Want to add a few ASSERT to check corner cases.
When I add the following code in main.c
__ASSERT(buf == NULL,"Test ","Test");
The module...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello,
with my nrf52dk board i had made some tests to check the scan performance.
Using nrf Sniffer - with Wireshark
nrf Mesh - LightSwitch Client (Mesh SDK v4.2...
Hi！
I'm working on direction finding. I'm using a nrf52833dk as a beacon, a nrf52833dk and a Direction Finding Antenna Board (PCA2005) as a locator for a bluetooth direction...
Hello,
I was trying to store some information in flash using littlefs. when I build and run the littlefs example alone it works fine as accepted. However, when I configure...
I have nRF52840 Dongle and I want to sniff packets between two BLE devices. When I search in the Nordic DevZone forum, there are inconsistent answer about BLE sniffing support...
Hello community!
I know this sounds almost impossible... but it's happening
I'm debugging an application based on peripheral_uart. When I call
bt_nus_send(NULL...
hello. I want to use the button as a pull-down. I am using nrf52832, and the button and circuit part are composed of pull-down and the code is written as follows.
However...
Hello,
I can't find anywhere the height dimension for the nRF52832 WLCSP. There is width, length but no height, what is the height of this product ? Thank you
I am trying to use puncover to estimate the maximum stack size for the created thread.
We also tried the thread analyzer, but gave up on it because it did not seem to be...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am using S112 softdevice along with SDK 15.1.1. The chip that I am using is nRF52832 and ble uart example
I want to make advertisement non connectable and non scannable...
