I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
Hello,
I am currently working on the NRFX QDEC library with a decoder to be used with a servo motor.
We manage to initialize and enable the QDEC and IRQ and we get...
Hi,
I am facing a problem in adding a power down feature in my application, the details of the application are as follows,
I am using the sensor server example given...
Hey guys,
I have a small concern and decided to ask here, as i was not able to found answer neither in zephyr or nrf sdk docs (not even sure which one apply to my question...
I use the DF example.In Rx.i use both nrf52833 boards as test.i use NCS 1.9.1.
In rx,i use the silab's 16 antenna array for receving antenna array.
because it has 16 antennas...
Topology:
Raspberry Pi A Raspberry Pi B
|(USB connect) |(USB connect)
nRF52840 dongle A )))) Thread (((( nRF52840 dongle B
Software:
nrf52840-dongle: ot-rcp.hex...
Hi,
The Evaluation board seems to have a footprint for nRF9160 non conventional.
The middle on TopLayer is a sort of Grid connected to the GND and Track to link Vias...
In the online power profiler for nRF52832, when I look at the advertising (Tx/Rx) power consumption I see that if I set the Tx payload to 0 bytes the Tx time modeled is 128us...
Hello,
In my project i want two use two UART as off now i am using app_ble_uart example since by default 6,8 is tx and rx pins respectively. so overall application of my...
Hello everyone
I am working on nRF52DK devkit. I want to check the SPI waveform. Actually I want to interface waveshare e-paper display (1.54 inch) For that i used GFX...
On the Thingy 91, the default configuration allocates a lot of flash space to several mcuboot partitions, leaving only 380kb for the app.
I need more space for the app,...
I have a custom application that works well for my nRF52832 device, but my team is moving on to an nRF52840 chip. Long ago, I deleted the directories that were not /pca10040...
I am using the UART multi-central example (from GITHUB) and connecting multuple peripherlas each streaming data at 38K
The multi-central is gathering the data from the various...
