Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
Hello,
I am using an nrf5340-DK board and the SDK 1.9.0.
I want integrate the FOTA functionality into the example which was provided by Nordic Semi:
nRF Connect SDK...
Hello all,
referring to this tutorial https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentSortBy...
I want to change the connection params in peripheral role with nrf52840 without informing the central device to do the actual setting operation, yet I don't find a relevant...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi,
I saw that the problem i am experiencing has already been described and reproduced in this ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/87295/busfault-when...
Hello,
We have to program an external QSPI flash which is connected to an nrf52840 SoC using the J-Flash application from SEGGER.
For this requirement I followed the instruction...
I get the following error if I try to unprovision device via ADV Bearer:
Problem is reproducible on "ncs\v1.7.0\nrf\samples\bluetooth\mesh\light" project if Light CTL...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
zigbee stops working when I use timer 2 for asynchronous UARTE operation. Tell me where to see which stack uses which periphery. Or is it some kind of mistake on my part?...
Hello,
In my project i am using nrf52840 and i have change the default UART pins to P1.3 (TX) and P1.4(RX) and while using virtual UART like BLE UART i mean in the sense...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Looking through the forum, I found this great post with an awesome and very helpful document that displays the ins and outs of BLE on Android ( BLE_on_Android_v1.0.1.pdf ...
Hi, I want to upload the code to external nrf52832 chip(which is on the custom-made PCB) using nrf52DK board.
First, I tried to check uploading the nrf52832 chip on nrf52DK...
Hello Devzone Community,
My name is Ted, and I am continuing work on an nRF9160 based, battery powered custom board firmware. I recently posted a couple of tickets here...
Hello. I am doing current measurements on nrf9160dk while sending ~1kb json file through mqtt. I am following this guide: https://infocenter.nordicsemi.com/topic/ug_nrf91_dk...
I added some code for events of an external device. The external device is configured to Listen and Submit events as other Modules do. When, the generated Hex is burnt in...
I've been referencing these two tickets pretty closely How to specify signing the key with MCUBoot - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) and MCUBoot...
Hello, Dear Kenneth.
Thank you very much for your response and the answer.
I will change the hardware solution using a voltage detector, but I am not clear yet on the...
Hi, i have this message after installing nrfutil
I checked version of the python, checked requirements, tried to install from sources. I do not know what to do next
