hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello Support, I'm looking for reference schematic for the interface between nrf52840 (or similar) and the nrf21540 . Is there a simpler version than the developer kit user...
Hello again,
I'm trying to lower the power consumption of my thingy91 by turning off the serial by setting config_serial=n. Unfortunately, this causes a crash while running...
Hi I would like to start developing wireless and embedded solutions using Nordic Ecosystem SoCs. I will probably only need to use BLE 5.0 and maybe Bluetooth Mesh so nRF5...
Hi,
So we have a project where we use the NUS, and we need to detect when a client subscribes. We eventually found a way, but it seems very obtuse and a bit black magic...
Hello,
I'm working on a BLE application using zephyr and nRF Connect SDK 1.8.0 on the nrf52840. I'm debugging the BLE stack using ozone but whenever I set breakpoints the...
My Current nRF Connect SDK version: 1.5.0
I am trying to follow this reference https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/samples/nrf5340/netboot/README...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hi
I'm using the GNSS sample. It gives me an output, but I want to interpret the output of it. How can I read this and translate it to coordinates?
Kind regards
Sarah...
Hi,
I installed nRF Connect SDK (1.9.1) using Toolchain Manager v0.10.3, and nRF Connect for Desktop v3.11.0. Before that I also installed NRF command line tools 10.15.4...
hi,
I want to build and flash only mcumgr bootloader code to my controller , from the example which i observed i am getting that mcumgr is always with some other example...
I use an InsightSIP ISP1907-HT module, I have a 4 layer board to minimise cost. Signals on top and bottom with GND on inside.
I'm concerned that my design could fail emmissions...
Can using whitelist on Central and Peripheral reduce the connection time? In my example I want to advertise every 3secs and want to make sure that the central connects to...
I am completely new to this toolchain and how it works.
I was trying to add a UART sensor to the matter sample project on the nrf52840dk. Is there anyone who can help me...
Hello,
I'm using the flash MX25L1283 together with the NRF52840. I've implemented a new driver for that flash using the nrfx library. Everything works fine !
However,...
