Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned.
I want to know...
Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
To tell a central device to refresh the service list, I have enabled NRF_SDH_BLE_SERVICE_CHANGED. However, when I do this all/most of my existing custom characteristics start...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hello,
Our project is based on the "ble_app_template" example with added BLE custom profile.
We have been developing our software on the u-blox "BMD-300 evaluation board...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I had toolchain manager 0.10.3 and a project using NCS 1.91. Unfortenuately I have updated the Toolchain manager to 1.0.0 and now my project does no longer show up and the...
Hi
I have build a sample project nRF5430_audio for nRF5340 Auido DK(two DK, one for gateway, one for headset), following the guide: nRF5340 Audio — nRF Connect SDK 2.0.99...
Hi,
I work on a project that uses the dfu target library for firmware updates. This has been working flawless until I added task watchdogs.
The problem that I see is that...
Hello,
--> I want to read some analog values from Pressure sensor. I don't know how to read analog input from sensor. Can you give/provide me the code which having an only...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
I want to use the external flash memory MX25R6435F to run my code which has a big size on my arduino nano 33 ble but I'am a newbie and I don't find supports that can help...
I use PCA10059 demo board,receive BT data by" nrf connect for desktop",yesterday it is ok,but today when I plug it into my PC,it can't be recognized.and no any indicator,...
Hello,
In the Zigbee Network Coordinator example when flashing new file to nrf52840-DK the Zigbee network steering automatically starts. How do I disable auto-start of network...
