I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I have an "Aqara Wireless Mini Switch" ( https://www.amazon.com/gp/product/B07D19YXND ) which identifies as a Xiaomi WXKG11LM. This button is designed to send semi-nonstandard...
I'm trying to receive an HTTP response of approximately 100KB using the nrf9160 modem. When the response size is small recv works fine. When response is large recv returns...
GReetings,
Having a hard time using nRF Connect v3.11.1 for Desktop freshly installed on a Windows based laptop (Windows 10 Family 21H2)
J-Link V7.58b was installed simultaneously...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I have a nRF9160DK and am trying to install the nRF Connect SDK and have run into troubles. First, I am unable to launch VS Code from the Toolchain Manager. I have seen...
Good morning!
I am testing an application on Visual Studio Code + nRF Connect. I have a crash:
<err> os: Faulting instruction address (r15/pc): 0x0002c064
How can...
I have code that looks something like this:
static void some_worker(struct k_work *work) { struct state *state = CONTAINER_OF(work, struct state, some_work); k_spinlock_key_t...
My DK is connected via USB to my PC.
Uptill tommorrow it was connected and today it is saying not connected.
How to fix this ? Not sure what happened.
See below:
Have been trying to run nRF9160 sample code, including LwM2M client, and at client (latest nRF9160 firmware 1.3.2, latest SDK and Link Monitor 2.0.1) but in LTE Link Monitor...
I am unable to properly erase UICR registers on network core.
flash_erase() function that I call before flash_write() doesn't take any effect.
Example: 1. Set UICR->CUSTOMER...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
The MenuConfig page of SEGGER IDE (ncs1.9.1)：
How should I configure this interface if I want to configure usb DFU and trigger upgrade mode via button: 1.boot_usb_dfu\Use...
I am trying to use the DTM example for nRF5340 DK (PCA10095). The example is located at "C:\v1.7.0\nrf\samples\bluetooth\direct_test_mode", but I am facing "NRF_RADIO_Type...
In general, what are the steps to adding a device using GPIO pins.
My thoughts are to physically connect my peripheral to the board and configure the device tree using an...
Hello Nordic Team,
I have a nRF52833 DK with me.
I am using nRF Connect SDK v1.8.0 and through that using Segger Embedded studio loaded the Light switch example to nRF52833...
