I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi Sirs,
Is there document to describe the NFC ANT traces impedance control, likely differentail 100ohm, tuning method, and length match if there is?
Thanks,
Wilson...
Hi All!
Can you please help me that how to add the concurrent connection feature in the ble_app_uart_c example? The reason is that I want to connect the multiple concurrent...
Hi All,
We are developing firmware for our product that is manufactured by an external manufacturing company.
During production the manufacturer will need to program...
Dear all,
I'm running into the following issue:
Hardware
nRF5340-DK, 2.0.0, 2021.42
Software
SES for ARM Nordic Edition, V5.68 (64-bit)
nRF-Command-Line-Tools...
Hi,
I am new to the nRF environment. I am working with a custom nrf52840 board, and am trying to get the secure_bootloader example to work to flash OTA. I have gotten other...
Hi.
I am developing the nrf52832 seger embedded studio.
I tried to use mutex using nrf_mtx.h, but there was an error.
I don't know why this error is coming out...
I adding custom module o asset_tracker_v2. In Main.c using the function static void data_get(void ) , various data requests are added using the instruction:
app_module_event...
Dear Nordic Engineers
I use NCS 1.9.1 test Advertising Extensions,I have a problem.
I use softdevice controller,if I not set "CONFIG_BT_LL_SW_SPLIT=y",the program will...
Hi Nordic,
One of my customer is evaluate Thread for their product.
They can set up the Thread network with nRF52840DK now.
But we can't found the API of transmit...
Hi,
We are developing a custom hardware that has MDBT42 module with nRF52832 chip on it. Our project is based on the ble-throughput example and this module is using the...
Seems like this issue has been happening to people for a long time.
I'm on V1.91, Mac, trying to open in Segger embedded studio. Fresh install, select open nrf connect project...
Hi Support,
i did some changes(add some folder ) in gps sample program for nRF9160DK(v1.1.0) and using nRF SDK connect , toolchain 1.7.1, and getting error ( error: Aborting...
Hello
I am working on to flash my firmware binary into external flash by using nrfjprog commandline tools.
I have used below command to program and verify the external...
HI,
I am using BL653dvk board(customized ). I am following this link ( https://devzone.nordicsemi.com/f/nordic-q-a/82430/ncs-external-flash-ota-change-qspi-to-spi ) and...
Hi ,
IDE: SES
NCS version: 1.9.1
I install the development enviroment following this article. 开发你的第一个nRF Connect SDK(NCS)/Zephyr应用程序 - iini - 博客园 (cnblogs.com)
I use...
