Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello,
We have to program an external QSPI flash which is connected to an nrf52840 SoC using the J-Flash application from SEGGER.
For this requirement I followed the instruction...
I get the following error if I try to unprovision device via ADV Bearer:
Problem is reproducible on "ncs\v1.7.0\nrf\samples\bluetooth\mesh\light" project if Light CTL...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
zigbee stops working when I use timer 2 for asynchronous UARTE operation. Tell me where to see which stack uses which periphery. Or is it some kind of mistake on my part?...
Hello,
In my project i am using nrf52840 and i have change the default UART pins to P1.3 (TX) and P1.4(RX) and while using virtual UART like BLE UART i mean in the sense...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Looking through the forum, I found this great post with an awesome and very helpful document that displays the ins and outs of BLE on Android ( BLE_on_Android_v1.0.1.pdf ...
Hi, I want to upload the code to external nrf52832 chip(which is on the custom-made PCB) using nrf52DK board.
First, I tried to check uploading the nrf52832 chip on nrf52DK...
Hello Devzone Community,
My name is Ted, and I am continuing work on an nRF9160 based, battery powered custom board firmware. I recently posted a couple of tickets here...
Hello. I am doing current measurements on nrf9160dk while sending ~1kb json file through mqtt. I am following this guide: https://infocenter.nordicsemi.com/topic/ug_nrf91_dk...
I added some code for events of an external device. The external device is configured to Listen and Submit events as other Modules do. When, the generated Hex is burnt in...
I've been referencing these two tickets pretty closely How to specify signing the key with MCUBoot - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) and MCUBoot...
Hello, Dear Kenneth.
Thank you very much for your response and the answer.
I will change the hardware solution using a voltage detector, but I am not clear yet on the...
Hi, i have this message after installing nrfutil
I checked version of the python, checked requirements, tried to install from sources. I do not know what to do next
