Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
I want to use Flash Data Storage library to operate with data on external memory, connected through QSPI. So, as I see in this thread it should be possible, but for...
I am using the SD card driver from nRF5 SDK v17.0.2. Device nrf52840, IDE Segger, Custom PCB. nRF52 DK as progremmer.
There are problems when deinitializing the SD card...
Hi, can i modify USB_MSC example in sdk-17.1.0 to work with SPI instead of QSPI ? as i am working with NAND memory which not compatible with QSPI driver. but it works well...
I asked this question in a different form but not getting any answers on that thread.
My goal is to publish battery level messages to a certain address and receive it on...
Hello Nordic,
I'm using the official DTM routine to do "SDPPI" certification for Indonesia, but I don't have any test process for Indonesian test engineers to use. Does...
Hi there, we have many nRF52840 devices in the field that currently run firmware based on the nRF5 SDK. We'd like to port our codebase to the nRF Connect SDK for all new products...
I installed nRF Connect SDK 1.7.0 from scratch using the nRF Connect for Desktop toolchain manager plugin. All components are up-to-date.
Due to whatever reason all calls...
Hello,
I'm trying to publish values using a predefined message context.
This works fine when using bt_mesh_onoff_srv_pub or bt_mesh_lvl_srv_pub, but I get a crash...
Hej!
Do you have a reference design for nRF52840 and nRF21540, how to connect the ANT signal (nRF52840) to TRX (nRF21540)?
Is it enough to only use a DC block, C1=1.0pF...
Dear All
I used nRF24L01 antennas with external antenna for data reception and transmission at different speeds (256KBPS, 1MBPS and 2MBPS) for a while everything worked...
Hi
I'm having trouble when trying to connect nRF 52 DK with BLE app on nRF connect for desktop.
I can select device of my nRF52 DK, but cannot not scan any discovered...
HI Nordic, I've looked through all the documentation and tried a bunch of failed experiments...so I thought i'd ask you. On the nrf52840-DK, I'd like to
Connect the DK...
Hi,
I want to program my nRF52833 has tx. The example is provided for pca 10056 and pca 10040. I know that it's possible to change the configuration to use it on pca 10100...
Hello,
I am creating a BLE Rx/Tx connection between two NRF52840-DK's similar to the Nordic UART Service. With the goal to achieve around a 100/100 KB/s connection. Only...
